EW30DS75KS1 Electrolux Range - Instructions

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Very easy just had to pull the wire up that holds it secure.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

First, I watched a lot of videos on YouTube. All of them were very similar, and had similar repair instructions, doing all the work at the site of the regulator location. The gas supply flex line was easily detached, as well as the line that exited the regulator to feed the stove. The gas inlet nipple, however, was not willing to unscrew. My regulator was held on by Phillips head sheet metal screws, which were easy enough to unscrew, so I just removed the regulator, still attached to the gas connection nipple. I went to my shop and placed the regulator in a vise, careful to clamp either end, not the regulator valve itself, and used a deep socket over the nipple, and had to use a Breaker Bar to loosen the nipple. I cleaned the nipple where Pipe Dope had been used, and applied new sealant, then screwed it back on the the Regulator, once again using the socket and bar. Then I threaded the new regulator body with the sheet metal screws while it was clamped in the vise. (The new regulator was not threaded, and I had to use vise grips to hold the screws while turning them in) After that, installation of the new regulator was relatively easy. I wish Frigidaire had used hex head screws instead of the Phillips. After install, range worked perfectly. PartSelect delivered correct part in a timely manner.

First of all I am not Betty, I am her husband. Second I and a friend pulled the range out of the countertop (which was not necessary). The top can be raised on it hinges and the plate under the burners can be removed by taking out 8 to 19 screws and there is the thermostat looking at you. After doing this once and knowing where the thermostat is, the job could be done in less that an hour.. INSTRUCTIONS: Turn OFF the circuit breaker. Remove the burners. Remove the plate under the burners. Change the thermostat (making sure to place in correct direction as the one removed). Reassemble, turn on circuit breaker, test oven heat.

replaced it

Remove two screws in back to release the top.
Lift the top from the back and pull backwards to remove.
Open washer door and unscrew two screws to release the switch.
Reach down inside from the front and remove the switch.
Unplug the switch and replace with the new one. Reverse the process to install.
I found it easier to have someone hold the switch while I screwed it back in.

I removed the defective knob (which was easy to do, because it was not seated....just sitting on the metal head, but disconnected). I lined up the new knob and pushed down gently.

I turned the knob and the burner lit the way it was supposed to!

on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.