EW23CS85KS1 Electrolux Refrigerator - Instructions

Followed the online video from this site

The repair went easily after watching the video, took me less than an hour to complete the repair.

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on e ... Read more ach side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Took out old replaced with new. Now it makes ice

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to p ... Read more osition.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

Removed evaporator cover and dismounted evaporator coil. Threading in the new heater was difficult but not impossible.

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

I changed the defrost thermostat and the heater.

Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !

I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I wen ... Read more t and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!

1. Using Philips head screwdriver, remove plastic hinge cover on top of refrigerator door.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replac ... Read more e fridge door using reverse steps.
8. Enjoy your handi-work.

Followed install instructions on utube. Once freezer was empty, back panel was easily removed, and defrost thermostat was in plain sight, and easy to replace. Hope that solved my problem. Refrigerator has been plugged in for four days now, and is cooling properly so far.

Very simple less then five minutes.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the ... Read more slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.