EMO3000HCC03 General Electric Microwave - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cooking Tray motor failed
Found this site, was able to identify the specific part through the internal search engine, very user friendly.
Read what others had said about similar repair. Now with confidence, removed screws, got easy access to the motor, removed motor, installed new motor, re-installed bottom cover, done!
If you have electric burner or gas stove, I suggest laying down a towel or similar cloth. In the event you drop a screw, you done want it bouncing off the stove surface, or down into the burner dishes.
Great site, great resource, super fast shipping.
Read what others had said about similar repair. Now with confidence, removed screws, got easy access to the motor, removed motor, installed new motor, re-installed bottom cover, done!
If you have electric burner or gas stove, I suggest laying down a towel or similar cloth. In the event you drop a screw, you done want it bouncing off the stove surface, or down into the burner dishes.
Great site, great resource, super fast shipping.
Parts Used:
-
kEN from Southborough, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke light fixture socket
Rather than open access door took off bottom (5 screws) This gave more room as the microwave is mounted under the wall cabinets over the stove.
Parts Used:
-
Norman from Benson, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light socket replacement
I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.
Parts Used:
-
lester from orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to microwave
Had trouble isolating the problem, so I had a repairman identify the problem, then I ordered the part and replaced it myself.
Removed screws holding the grill in place. Removed air filter, removed screw holding plate under the filter in place. Reached in under fan cowling to find the thermostat cut-out. Disconnected the two wires. Put the new thermostat in place. Replaced screws plates and filter in reverse order.
Removed screws holding the grill in place. Removed air filter, removed screw holding plate under the filter in place. Reached in under fan cowling to find the thermostat cut-out. Disconnected the two wires. Put the new thermostat in place. Replaced screws plates and filter in reverse order.
Parts Used:
-
James from Highland, UT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
14 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The display screen would flicker and shut the microwave down after a couple of seconds
i removed the front panel by removing the two screws on the top fan shroud then remove the shroud. then i removed the one screw over the main control panel and slid it down to unlatch it from the unit itself. i then removed the ground wire thus allowing you to remove the panel enough to unplug the wires. there are 4 sets of plugs and a ribbon strip to remove. i removed the 3 screws holding the board and installed the new board.i replaced the screws,the ribbon strip, and the plugs. i then installed the ground and repositioned the main panel onto the unit and reinstalled the screws to the board and the fan shroud. i plugged the unit in. programmed the dash and away we went.. no problems thus far. i have noticed on the old board some components that have got hot and rusted due to excess moisture from forgetting to use the exhaust fan when cooking,boiling ect.. thus causing the board to malfunction. i hope this has been semi helpful..
Parts Used:
-
KIP from WOODBOURNE, NY
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
14 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light Socket replacement
I was told by 2 different appliance technicians that the crumbled/melted light socket could not be replaced which meant replacing the entire microwave (expensive!). Other posters on your sight described the repair steps and I gave it a try. The hardest part was probably figuring out which switch in the fuse box belonged to it (now marked clearly). It was a simple matter of unscrewing the bottom panel of the microwave to access the socket, pulling the crumbled/melted unit off and shoving the new one on. I can't believe the repairmen didn't want any part of even giving it a try.
Parts Used:
-
Jill from Arlington, TN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
11 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
A light burned out and fried the socket and wires.
The hard part was trying to figure out how to get to the light socket. It is a bulb in the floor of the microwave that lights the stove top. I found help at your website by typing in the model number to find the diagram of the parts list which showed how each part fit together (and thus how they came apart). So I could see how to take the bottom off the microwebb and get to the wiring for the bulb and the bulb socket as well. They both had to be replaced with parts ordered from PartSelect along with the wiring. Putting in the new was just a reverse opposition. I saved $200 for a repairman, by spending about $60.00 for parts. Our other choice was a new microwave - and a repairman to install.
Parts Used:
-
Billie from Georgetown, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
11 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave wouldn't start after "Start" pushed
Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again
Parts Used:
-
Don from Monte Sereno, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven blows 20 amp fuse
Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.
Parts Used:
-
PATRICK from Covington, LA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
12 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
grinding of microwave turntable
Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.
Parts Used:
-
William from Spring Hill, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bulbs broke off in socket, socket would not come out
I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you
thanks you
Parts Used:
-
William from Kingwood, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave turntable stopped turning
1. Turned off circuit breaker for microwave.
2. Removed screws holding the bottom cover of the microwave; cover is hinged at the back, so it dropped open and stayed out of the way.
3. Unplugged turntable motor and removed screws that hold turntable motor in place.
4. Pushed broken pieces of the plastic turntable coupler out of the way (hole for motor's axle not big enough to remove them).
5. Put turntable coupler into hole in bottom of microwave interior, held it in place while putting the motor axle into it from below.
6. Replaced screws holding turntable motor in place, plugged in motor's electrical connector.
7. Closed bottom cover and replaced screws that hold it in place.
8. Switched on microwave circuit breaker.
2. Removed screws holding the bottom cover of the microwave; cover is hinged at the back, so it dropped open and stayed out of the way.
3. Unplugged turntable motor and removed screws that hold turntable motor in place.
4. Pushed broken pieces of the plastic turntable coupler out of the way (hole for motor's axle not big enough to remove them).
5. Put turntable coupler into hole in bottom of microwave interior, held it in place while putting the motor axle into it from below.
6. Replaced screws holding turntable motor in place, plugged in motor's electrical connector.
7. Closed bottom cover and replaced screws that hold it in place.
8. Switched on microwave circuit breaker.
Parts Used:
-
David from San Diego, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave would not start
-
JULIA from JACKSONVILLE, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When you open the door at the start the fan wood come on
I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it
Parts Used:
-
Larry from CHARLOTTE, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
8 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave stays on when door opened
Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????
Parts Used:
-
Charles from OAKDALE, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!