EI30ES55LBB Electrolux Range - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the different sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.

Installation of the temparature sensor, one of the technician recommended parts took no time, just two screws and a snap off/snap on part. It did not fix the problem. I then replaced the main control panel, which requires more work, but didn't solce the ussue either. I then replaced the thermal fuse, which wasn't mentioned by tech support, and required much more disassebly of the top panels of the stove, with still no fix to the problem. I am waiting to replace the thermostat heat sensor unit, the only other part in the circuit controlling power supply, requiring removal of the stove top again,

removed the old burner and put the new one in it's place.

My husband followed the video instructions and it was easy to fix.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Removed screws on the sides and front.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Lifted stove top to disconnect burner wires in order to use stove until parts arrived. Remove a bunch of square drive screws to remove back panel from stove. Identify relay board and disconnect wire connectors from it then release several plastic clips and two screws holding board to oven. Install new board and connect wires, No other adjustments were required.

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

First of all I am not Betty, I am her husband. Second I and a friend pulled the range out of the countertop (which was not necessary). The top can be raised on it hinges and the plate under the burners can be removed by taking out 8 to 19 screws and there is the thermostat looking at you. After doing this once and knowing where the thermostat is, the job could be done in less that an hour.. INSTRUCTIONS: Turn OFF the circuit breaker. Remove the burners. Remove the plate under the burners. Change the thermostat (making sure to place in correct direction as the one removed). Reassemble, turn on circuit breaker, test oven heat.

Followed the parts select video. However there were differences. Four screws to release stovetop from brackets very difficult to break free even once correct bit identified. No spring clips but studded screw and coil springs let elements fall right off underside bracket. Need fours hands to hold back in place to screw bracket back in place to hold elements.

Remove two screws in back to release the top.
Lift the top from the back and pull backwards to remove.
Open washer door and unscrew two screws to release the switch.
Reach down inside from the front and remove the switch.
Unplug the switch and replace with the new one. Reverse the process to install.
I found it easier to have someone hold the switch while I screwed it back in.