All Installation Instructions for General Electric Dishwasher EDW4000G03CC

Detergent cap would not stay closed

After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.

Parts Used:

Detergent Dispenser with Rinse Cap

Michelle from Carlisle, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

one wheel was missing, others kept on falling off

Just snapped studs and wheels together and put them into place.

Parts Used:

Single Lower Wheel Stud/Axle

Lower Rack Wheel Kit - 8 Pack

ILONA from AUSTIN, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

axle for wheel was broken

Popped the axle on to the wheel, then snapped it on to the lower drawer - done!

Parts Used:

Single Lower Wheel Stud/Axle

Gail from Woodstock, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

some wheels had broken, was really hard to move rack in and out.

I am NOT handy, but my husband was gone when the wheels and stud/axles came. I was able to replace all of them in about ten minutes with no tools. Easy and no more frustrations!!!!!

Parts Used:

Single Lower Wheel Stud/Axle

Lower Rack Wheel Kit - 8 Pack

Kimberly from Durango, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Old rack was rusted out and missing most of the wheels.

Easiest repair ever. My new rack arrived in three days, opened the box and slid it in. Better quality than the original. Excellent service!

Parts Used:

Complete Lower Service Rack Assembly

Jim from Palatka, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

No water in

Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.

Parts Used:

Water Inlet Valve

Everett from FREDERICKSBRG, VA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Detergent dispenser did not work

Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.

Parts Used:

Detergent Dispenser with Rinse Cap

ARTHUR from OAK PARK, IL
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

wouldn't drain

Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.

Parts Used:

Check Valve Flapper

JOHN D. from GOSHEN, IN
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Roller Broken on dishwasher

Popped out Old Roller, put in new one, pushing it together with a pair of pliers.

My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item

Check all your rollers before you buy just one!!!!!

Parts Used:

Dishwasher Dishrack Rollers and Axles

Sean from Cicero, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken axle which hold wheel on lower rack

Easy install, snap in new axle and put wheel on stud. Be sure to check all wheels for any replacement due to heat melting wheels on rack.

Parts Used:

Single Lower Wheel Stud/Axle

Robert from WALNUT CREEK, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

old wheels kept falling off

Took stud out of old wheel, put new stud in. It was that easy!

Parts Used:

Single Lower Wheel Stud/Axle

Faye from E STROUDSBURG, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

its wasn't latching so the dishwasher wouldn't work unless i held the door in the whole time

I called your tech and she sent me a awesome video that made it so easy to fix on my own

Parts Used:

Door Latch

Michele from NEOLA, UT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken silverware basket

Pulled the old one out and placed the new one right into place

Parts Used:

Silverware Basket with Lids

Alan from MECHANICSVLLE, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Dishwasher was not starting

Replaced interlock assembly as one of the possible causes. The replacement was easy, but this was not the final fix. I also replaced the water inlet valve, flood switch and finally found that there was large calcification within the drain tube assembly (not visible, but was blocking water). Got a new flexible tubing and new drain hose, plugged everything together and the dishwasher runs like new now. Watching for a potential leak from the drain tube to drain hose connection and mya need to tape it up, but so far so good...

Parts Used: