E23CS75DSS4 Electrolux Refrigerator - Instructions

After taking the complete motor, tray, icemaker, etc out and finding no problem, I then finally checked for power at the connector at the top of the icemaker. I concluded that there was no pwoer going to the motor. I then removed the circiut board and found the relay for the auger was not working. Putting the new board in took 10-15 min. ... Read more and then the auger started to work.

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable ... Read more .

I had to remove the face cover to gain access to the ribbon harness, also had to remove the push pads The ribbon is a delicate item so care had to be taken not to bend the ends. The ribbon can fit either side so getting it in place to make contact was kind of tricky. After the ribbon was in, it just a matter of putting things back togethe ... Read more r. Dispenser is fixed at a minimum cost, ribbon was shipped within 2 days which was great. Thanks to Part Select for easy to find on the net, had a complete diagram of the refrigerator ice/water dispenser so finding the parts needed was simple. Doug

Repair man wanted a 130.00 service charge plus parts , With the help of YouTube we did the repairs inhouse , couldn't believe it was that easy. Refrigerator is working like a new one ,our maintenance crew has ice cubes were all happy !

I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no ... Read more reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.

The repair could not be completed. I ordered a thermostat defrost kit but received a collar arbor for a saw. They do not answer the phone at customer service and the order took close to two weeks to get in the first place. Beware of shopping at this site!

I removed the filter bypass from the box. I opened the refrigerator door. I put the filter bypass in the space where the filter was located. I closed the refrigerator door. I opened the freezer door. I turned on the ice maker. It worked.

Took me weeks to find the noise after I checked everything electrical in the house including replacing all batteries. Finally, an electrician isolated it to the refrigerator.

Frigidaire Model FRS26LH5DS9 Found several YouTube videos for reference.

Replaced the Run Capacitor and Compressor Start Relay.

U ... Read more nplug and remove the back panel. On the bottom left side, detach the two old parts together from the compressor. Use a large flat screwdriver to pry them out. (They are held in place with a wire you must first remove.) Plug one new part onto the other and then insert it as one part.

Easy Peasy. The hardest part is getting your hand in a small space and putting back the wire that holds them in.

Don't call a repairman - fix it yourself....

Popped out glass, pulled up and the front of cover and pulled froward. Pushed new cover back on to studs and pushed down on cover to lock it to front studs. Put glass on top of new cover. About 3 min total to make repair.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to ... Read more uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Removed the fridge door, replaced plastic Hinge Bearing, re-attached door. WhaLa - No more clicking!

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The door clunk problem was as others described. Repair similar to others described. The major thing to understand which I didn't see listed elsewhere is whether the top or bottom little nylon toothed cam is broken. This part is the one in the door. There was also one in the hinge, PS976594 or PS430814 ? I ordered this one and was luc ... Read more ky that it was correct. I'm not sure whether it's possible to know whether door side or hinge side is broken, without removing the door to see.

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure