DWD1500AWB Admiral Dishwasher - Instructions

first i removed the back of the dish washer door and determined the handle was broke.went online with you with model number and looked at the parts breakdown. ordered the latch assy,however the latch assy i ordered did not come with the handle,reordered handle and got latch assy and handle and it was cheaper--go figure! you guys were grea ... Read more t! received ra# for part to return asap and i'am very pleased! thankyou for your great service! i will tell others about your service! again thanks!

First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into posit ... Read more ion. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

Not a bad repair once you diagnose the problem. Took me three tries to figure it out. Just make sure you follow the instructions. I used an allen wrench to hold the motor in place while tightening the part onto the motor shaft, this way I didn't have to remove and flip the dishwasher to do the repair. The good news is the replacement part ... Read more I needed was metal instead of plastic, thus I should never have this problem again. I don't understand why it was plastic in the first place but all of my appliance problems seem to be made to fail after several years of service.
Repair was

I turned off the electricity at the circuit breaker. Sitting in a chair in front of the opened dishwasher with the partially opened door resting on my knees, I removed the 10 screws lining the inside of the door (setting them in order on the cabinet above -- 2 are different length so this helps keep them in order.
I tilted the inner ... Read more cover on the door up (which is what the screws had been holding). With the door not fully open because it was on my knees, I was able to position the cover so that I did not have to remove the connection to the soap dispenser.
The two middle screws removed earlier were the screws that held the latch in place, so the assembly was already loose at this point. I put a black mark on the assembly to mark the side that the black wires were attached. Then with the pliers removed the plugs that were connected to the switches on either side of the assembly. Then marked the replacement assembly with the black mark on the same side as the one removed. I attached the plugs to the the replacement assembly using the black mark as reminder for which side was which.
I lined up the latch on the door where it goes, lowered the lid (lifting the lower edge over the base a little), lined up and started the latch screws (middle 2), then started all of the other screws and then tightened them all. Closed the lid and tested the latch. It was closing correctly now. I turned on the electricity and tested to make sure all was now working properly.

I pulled the dishwasher out from under the countertop. It was quit easy to get to in the lower left front corner of the appliance. I loosened up the bracket that was holding the valve in place. Removed the wires, and taped and ID them so that I would know which one went where. Removed the hose clamp, pulled the hose off and removed the ... Read more old valve. Put the new one back in just as I removed the old one in the same order. It was a snap! This is not the first time I have used PartSelect! Our evaporate fan went out on our refrigerator a couple years ago, replaced that. A shelf broke in our refrigerator twice, each one different at different times bought both from Part Select. This is the first place I look for help with repairs! I at least attempt to save money, then if it's too difficult I will hire a repairman. So Far, PartSelect has saved me a lot of money on doing it myself! Thanks PartSelect for making small repairs easy to tackle yourself, along with reasonable prices for parts!

First I opened the breaker on the dishwasher removing power from the unit. Then I removed the Torx head screws on the cover on the back side of the front door. Then I pulled off the stainless steel sheet metal panel which exposed the door latch. Then I unplugged the electrical connectors to the two micro switches on the assembly, next ... Read more I plugged in the connectors on the new latch assembly and postioned the latch back on the mounting holes. Replaced the stainless steel sheet metal and put the screws back.

Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

after reading a article on problems the logic one was frist the door. Order the part ,took off the inter panel with star slot (10)exposed the handle and switch. Removed it, abit hard at frist,then replacement went in easy , the washer worked.
I guess I was lucky because on the other side of handle similar type of part thats maytag ... Read more for you.

The big problem is that you cannot purchase the wheels only. I found that out after ordering the rack track because that looked like what I needed. But it didn't come with the wheels. So I returned it. Then I went to the basement and found things in my junk boxes and fixed it without purchasing the complete parts. Cost: 10 cents for ... Read more two nuts vs $60 for the required parts.

We took out old racks and installed the new ones. On another note, after ordering (or trying to order) parts from appliances older than 10 years old several times, I think manufacturers stop making parts after 10 years. So if you're thinking of replacing a part on an older appliance, try to look for it sooner than later.

Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.

The part broke off a while ago, and I did not want to call a repair person. The machine still ran, so I ran it with the part missing - the glasses were not very clean, but the repair call was expensive...

I figured that I had a snowballs chance of finding the part number on a molded plastic piece with no numbers printed on ... Read more it. Boy was I wrong. I was able to choose the part off of a schematic of my machine right on the website and it linked me to the right part order form, so I did not even have to go back and find it on a list.

When the part came, all I had to do was unclip the old mount- with my fingers- no tools, and snap in the new part.

A for maytag for making it easy to fix
A+ for PartSelect for making it so darn easy

First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door pan ... Read more el using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

Accumulator was as easy as just removing srews and replacing the part. The Float I broke by accident and was more complicated to replace required 2 people to manage parts.
Dishes finally coming out clean!

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks