DW708 (Type 3) DeWALT Miter Saw - Parts

It is a genuine hardware that is supplied directly from original equipment manufacturer for use with Dewalt and Black and Decker power tools. This replacement screw is used to secure the field case. Please note this durable metal Torx screw is sold individually.

This manufacturer-sourced item is specially designed for use with DeWALT and Black and Decker saws. It is an identical replacement for a missing or damaged plug that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep i...Read moren mind this high-quality item is made of durable material and is sold individually.

This is an original replacement part sourced directly from the manufacturer. The spring is commonly found in miter saws from DeWALT and Black & Decker. This part is made of metal, and may be found in various locations in the machine, depending on model. Please refer to the parts diagram to be sure of ordering the correct part. You may...Read more require a screwdriver when replacing this item. The spring is sold as an individual replacement part.

This is an OEM part sourced directly from DeWalt for use with miter saws. This petroleum based grease is used to lubricate the system allowing for easy, low-friction movement while protecting parts from the usual wear. One 1.75 oz tube of grease is included per order.

This replacement field is specially designed for use with Bosch miter/circular saws. In conjunction with an armature it is what drives the unit. A field is usually damaged by overloading the power tool, or because of a bad armature. It is highly recommended to replace both carbon brushes when replacing a field. This item is sold individua...Read morelly. To complete this repair you would need a screwdriver. • Make sure the saw is unplugged • Remove brush covers and take out brushes • Remove the cap and the housing screws • Once the housing is removed you will have access to the field • Disconnect all wires leading from the field • Take out old field and replace it with a new one • Re-connect all the wires • Re-assemble the motor

This genuine OEM ball bearing is designed for use in DeWALT power tools and is sealed on both sides to protect against dust, debris, and moisture. Sold individually, this high-quality bearing helps reduce friction between rotating parts, allowing your tool to run smoothly and efficiently. Ball bearings play a crucial role in distributing ...Read moreload and minimizing wear by enabling smooth rotation with minimal contact. However, due to constant exposure to pressure, heat, vibration, and friction, bearings naturally wear over time. Replacing a worn bearing can restore performance and extend the life of your tool. If you notice unusual noise, vibration, or reduced efficiency, it may be time for a replacement.

It is a genuine DeWALT item that is supplied by the original equipment manufacturer for use with crosscut miter saws. The locking pin helps to secure components together. Unfortunately, over time it may wear out, get damaged or lost eventually requiring a replacement. Refer to the diagrams for your model to ensure the exact location and t...Read morehe correct application of this part. It is made of durable metal and is sold individually.

This is the handle for the trunnion, for correct application make sure to check appropriate diagrams of your model. It is an authentic replacement part that is supplied by original equipment manufacturer for use with Black and Decker and Dewalt miter saws. This part is made from durable metal and it is sold individually, please note the hardware to secure it is sold separately.

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 16 Gauge • 10 Feet Long

This replacement item is specially designed for Dewalt crosscut miter saws. It is a genuine OEM sourced item, not an aftermarket imitation. This assembly includes one armature with a plastic fan. It is highly recommended to replace both carbon brushes when replacing an armature. Please note, the bearing for the armature are not included, ...Read morethey are sold separately. Remember to be especially careful of the armature fan when you remove it, because if you break it, you will have to replace the entire armature. To replace this armature you will need a screwdriver.