DW570 (Type 1) DeWALT Hammer Drill - Parts

This rubber piece is a genuine OEM part manufactured for DeWALT and Black & Decker. It is sold individually. A cord protector attaches at the point of connection between cord and power tool. It protects cord and wires from damage caused by stress, strain, and motion. This repair is fairly simple and requires just a screwdriver. A damaged ...Read morecord must be replaced as well. Replacement cords are sold separately. • Unplug power tool • Remove the casing • Detach wires from tool • Slide cord protector onto cord • Reattach wires and casing • Test power tool

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is an original replacement part manufactured for use with rotary hammers. The special o-ring is commonly used to provide cushioning and spacing at the connection point between part assemblies. This o-ring is used with several different models of rotary hammers and the part application may vary depending on the model. The o-ring is so...Read moreld as an individual replacement part, please see model diagram for part location.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. The...Read morese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

It is a high quality hardware that is supplied directly from original equipment manufacturer for use with Dewalt and Black and Decker rotary demolition hammers. This replacement screw has several different applications depending on the model of your tool, please make sure to check appropriate diagrams for correct location and use of this hardware. Note that this replacement Torx screw is sold individually.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with demolition hammers from DeWalt and Black and Decker. The metal screw is commonly used to secure the fan assembly to the motor's armature. This item is available as an individual replacement part.

This is an authentic DeWalt replacement part, sourced from the original manufacturer for use with rotary hammers. The metal rod connects to the body of the handle and is used to set the drill depth. This item is available as an individual replacement part, please see illustrated part list for related parts.

This is an authentic DeWalt replacement part, sourced from the original manufacturer for use with rotary hammers. The special lever is used to when adjusting the tools settings. The lever is available as an individual replacement part, please see model diagram for associative parts.