Models > DPVH890EJ2MG > Instructions

DPVH890EJ2MG General Electric Dryer - Instructions

All Instructions for the DPVH890EJ2MG
106 - 116 of 116
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Screeching noise when drum went around
To get to where the drum slides go you have to first remove the dryer top. Then you have to remove the two screws that hold the dryer front/door. Found inside the dryer about an inch down on both sides. Be careful because it will fall off. Lower carefully as there is an electric hook-up on the bottom of the door. On the door top are the brackets that the slides slip into. My dryer has 4 slides. Sold individually for some reason. You are done except for re-assembly. Slip dryer drum back on door, press the front until you hear it click back together. Put screws back in and top back on. You are done and no more screeching!
Parts Used:
Drum Bearing Slide - Green (Sold individually)
  • Carol from Bristolville, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer was squeaking when drying clothes
replaced the parts that had worn out
Parts Used:
Drum Bearing Slide - Green (Sold individually)
  • John from Oxford, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door would not close
Removed door strike and latch, replaced, works like new.
Parts Used:
Door Latch Door Strike
  • Arlie from Ringoes, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Horrible squeaking noise during operation
The only tool used was a phillips head screwdriver. I removed two screws to lift the lid and two more screws to free the front panel, slid off the front panel, and had direct access to all 4 slides, replaced, reassembled, and good as new.
Parts Used:
Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • Angelica from Fayetteville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
horrible shreaking noise
follow the video, and in no time fix and ran smooth, like brand new, love this website, fast and reliable
Parts Used:
Drum Bearing Slide - Green (Sold individually)
  • angela from Delaware, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer did not latch
easy to fix took less than 10 minutes
Parts Used:
Door Strike
  • janet from martinsville, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Parts Used:
Door Latch
  • Fawn from Loganville, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Intermittent squeak when first starting the dryer.
Followed the video on this site but did not have to remove wires. Just stand in front and let the front panel rest on your leg while you replace the slides. Quick and Easy!!!!
Parts Used:
Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • Kevin from LIncoln, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Intermittent Squeek Noise
Removed 2 screws from inside door lifted top panel up,removed 1 screw attaching front panel to left side. Pulled front panel out far enough to remove and replace slider bearing.
Parts Used:
Drum Bearing Slide - Green (Sold individually)
  • Dana M from Middleport, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Clothes would get caught in the drum slide
The clothes would get caught where the drum slide should be (it was almost totally worn down) and would leave black marks. I watched Parts Select youtube video. Bought the parts needed from Parts Select. They arrived within a couple of days. I replaced the 2 drum slides and no more getting caught. Took about 20 minutes.
Parts Used:
Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • Daniel from Baton Rouge, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dry squealed so loud you needed ear plugs!
The repair was extremely easy to do. The video was perfectly done and described everything one needed to do in very simplistic details.
Parts Used:
Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • Warren from Tyndall AFB, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DPVH890EJ2MG
106 - 116 of 116
Back to Top