DLE0442W01 LG Dryer - Instructions

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any su ... Read more ggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before workin ... Read more g on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

First, I set my laptop up in the laundry room, and went onto Youtube, searched LG dryer repair sensor install. then went step by step, pausing the video and starting it as I went. Then I Plugged it in and it worked. For $50 and some time I was able to do it, the prices from partselect are great and the turn around on shipping was super fa ... Read more st. Thank you Partselect. Kevin

My lg electric dryer would not heat up. I went on line and found that the thermostats (there are two) could cause this problem. I used my dvm to ohm out the thermostats and found that the high heat thermostat was open. I replaced this thermostat and the dryer ran for a little while and then quit heating. When I checked the high heat ... Read more thermostat again I found it to be open again. I then ordered and replaced both thermostats and the dryer has been working well since. The hardest part about this repair was the job of taking the dryer drum out to access the thermostats. I did however get good at doing this.

Removed Top, then front and drum. Parts easy to access once drum is out. Recommend reading up on drum replacement. Would appear that all repairs will require taking it out.

Seemed to be shutting off on the safety thermostat so I replaced them all. Works.

Found YouTube video followed it closely and did extensive cleaning. The lint on the felt of the drum was causing a rough rotation as well.

well after hurricane sandy we had a family of 5 stay with us. after the storm we retrieved most of thier clothing and started washing. the machine worked off of a generator for 4 days almost around the clock. overloaded at times i might add. these folks lost just about everything. my wife noticed a noise i opened the machine and saw the c ... Read more racked drum. i ordered a new one from you guys and saved the $900 on a new machine. together we breathed new life into it. thanks!!!

Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (t ... Read more o my surprise without any extra screws or parts left). Fairly easy job, just time consuming.

I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.

First the delivery time was incredible, I ordered the part at 2pm on Mnday and recieved the drum Tuesday afternoon. I'm not sure how this was accomplished as I can't even mail a letter across town and receive the next day. Reoved front of dryer removed old drum and slid in new drum. only difficulty was the wiring disconnect on the cont ... Read more rol board, didn't want to come off. took 5 minutes to work loose.

Unscrew and replace locker hook and assembly, replace screws. That completes door locking assembly repair. To replace the rollers and safety switch assembly, remove back top and front of dryer. Detach and remove control panel and set aside. Remove blower tube at bottom of drum and set all parts and screws aside. Detach all necessary parts ... Read more and depress belt idler pully underneath drum and remove belt. Remove drum and unbolt rollers on the front panel and also on back of dryer. Remove triangular washer and be sure not to damage it. Check axles for damage, and replace new rollers onto axles. Replace all washers and triangular washer and bolt back onto dryer tightly. Be sure to check that all rollers are spinning freely and adjust bolt tightness accordingly. At some point replace dryer door safety switch by pushing it in from the outside. That completes the safety switch repair. Now once all rollers are replaced, reinstall drum and depress idler pully and reinstall the belt untiltension is restored. Reassemble all parts and plug all wiring back in to proper places. Screw everything back together, plug in dryer and start a cycle to confirm repair was effective. This is not a complete guide on the repair, just a basic idea of how I did it. I Googled videos on how it is done and that was of great help. The repair is actually pretty easy but is much easier with two people. There are some other steps but they should be obvious along the way. My dryer runs almost better than new and the repair was pretty easy and straight forward. It is most definitely a repair you can do yourself. Hope this helps you out.

Easy repair, more time spent de-linting the inside of the machine and the duct system.

The repair was not that difficult but one thing led to another(a small plastic part rolled under the dryer and then the plastic vent pipe broke from age when we pulled the dryer out to find it) and we discovered that the biggest problem was that the pesky ground squirrels in our area had taken up residence in our dryer vent. We found a d ... Read more ead one that had come all the way into the dryer along with the acorn shells it had been eating. The vent itself was almost totally clogged with lint. The flap on the outside was stuck open allowing the ground squirrels to come in and find a nice warm, soft place in which to live. Now the dryer works like a charm but if we hadn't decided to change the gasket we would still be complaining about how long it takes to dry a load of clothes.