DISR473CGAWW General Electric Dryer - Instructions

I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.

Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!

Unscrewed three screws on back and removed the switch and inserted the new one. There are 3 wires that clamp on the switch. Remember to unplug before doing this.

Real easy and great people to work with. Much cheaper than a technician repair.

Jim

took out broken filter and replaced with new lint
filter.

I narrowed the porblem down to the rotary start switch, which is located in the top panel. It takes a hex wrench to remove the four screws holding the fron top panel in place and of course the knobs had to be removed. The switch rotates about a wuarter of a turn to come out. Label and remove the three connectors (3). It took about a week to get the replacement part which was slightly different than the original part. The good thing is it had the three prongs like the old part.. I hooked the connectors in the same configuration as the old switch, plugged the power cord back in to test and it started right up.

took two screws off the front. They were behind the door. These screws held the top on. Lifted top off and took two screws from the frame holding the front door and panel on. Disconnected three wires and removed front panel. Laid dryer over on right side and removed four screws from bottom and back,two from control panel and removed left side.lifted drum out and removed belt. Removed nut cap and idler pulley wheel. Replaced same. removed three screws holding screen and rear drum bearing to drum. Replaced same. Removed electric heat coils from back and removed receiver for rear drum bearing. Replaced same. Put everything back in reverse order. Works better than new!!

Pulled off old knob put on new one

Removed the broken handle from the dryer and popped on the new one.

First remove top cabinet panel by removing two small screws under door recess; then swing up lid and remove from hinged area at the rear. Once top panel is removed, remove the front panel and door assembly by removing two attach screws securing front panel to dryer cabinet. Swing the front panel down and remove from two base hinge points. Slightly lift the front of the dryer drum and wedge some rolled up newspaper between drum and frame to provide access to get your hands through to the idler pulley and motor area. Remove the belt form the motor & idler pulley; then slide the drum out of the cabinet to gain access to the idler pulley. Remove nut securing idler pulley from bracket and remove and replace with new part. Reverse the process to complete the installation.

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

Ordered new lint filter, received it in 2 days, removed old filter, snapped in new filter, patted myself on the back .

The part was delivered in record time. That was the best part. And it fit perfectly and was the correct color. The other filter was grey and the dryer is white. Thanks for being so efficient.

Unplug. Remove 3 knobs at front of panel. Remove 4 screws. Panel pulls forward. Remove green grounding wire to allow panel to come forward more. Pry up locking tab on switch. Turn switch to unlock from panel. Install new switch in reverse order of removal. Pull off each wire one at a time from old switch and attach to new switch. Reinstall panel and insert 4 screws. Done. My wife was so suprised that it actually worked and I fixed it in less than a day! Only took about 20 minutes. Thanks Part Select and the other repair stories that I read on your website.

Advice from others with same problem on your web site was very helpful. I removed one of the three torx screws holding the deflecter, Used 2.5 star-drive screw diver bit and cordless drill/driver. Replaced 2 of three torx screws holding the deflecter with the headless brass screws, Using vice grip to tighten. Removed third torx screw and removed old deflector. Used shop vac to clean behind it. Installed new deflector, sliding it over the 2 headless screws, then installing one of the torx screws, then replacing the brass screws with original torx screws, one at a time.

watched the video on your website,this made repair to the dryer very easy.hardest step in the repair was getting the belt hooked up on motor and tensioner,but being old and persistent i finally won!