All Installation Instructions for Frigidaire DGHD2361TF1

Water outlet tubing leaking in elbow behind water filter

Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.

Parts Used:

TUBE-WATER INLET

Chuck from GRIFTON, NC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original ice maker not working leaking water water out door

Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.

Parts Used:

Ice Maker Assembly

Michael from FREE SOIL, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

R/S fruit & vegetable drawer L/S roller holder broke.

I removed the r/s drawer, removed the r/s shelf, transferred the metal brackets to the new shelf & reversed the procedure to reinstall.

Parts Used:

Rail - Left Side

Michael from MARTINSVILLE, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Slide assembly broke on left side of freezer drawer.

Took front of door off, took out freezer basket removed one screw, took off old part and put on new part, put everything back together and it was done. 15 minutes done.

Parts Used:

SLIDE ASSEMBLY

Garry from FREE SOIL, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

From day one the installer did not tighten the screw in the freezer handle. It finally came apart. They didn't leave me the Allen wrench for my fridge.

Simple tightening of the screw with the right tool.

Parts Used:

WRENCH

Margaret from WINDER, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The fridge icemaker would pit out crushed ice. No whole cubes

I had to remove everything inside including the surrounding box and disconnect all the wire connector s. The solenoid that was bad was behind the cover that the auger motor cover. . Job was easy after I determined I had to remove everything that was not attached to the back wall.

Parts Used:

MODULE

Gerald from MERIDIAN, MS
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Removed old rail installed new rail

Removed screws and rail and installed rail and screws

Parts Used:

Rail - Left Side

ROLLER

John from PASADENA, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

A set scew was ordered twice.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.

The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

Parts Used:

Screw

Susan from BRAINTREE, VT
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No problems

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

Parts Used:

Screw

Nancy from LEHIGH ACRES, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ICE WOULDN'T DISPENSE FROM ICE BOX

I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.

Parts Used:

BAR-DRIVE

James from ORLANDO, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ice maker is stuck on crushed ice.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

Parts Used: