DFSS9VKBASS General Electric Refrigerator - Instructions

I took out the old one and put in the new. 15 seconds.

replaced lights in refrigirator and freezer

Replacement ice maker was plug in unit, only needed to remove one screw holding plastic plate that hid plug and wiring. Plugged it in and reattached plate with screw and done!

Hardest part of repair was getting frig. away from cabinets to unplug it.
Turn off water to ice maker.
Phillips's screwdriver to take off the cover of the electrical connection to
the icemaker tip it outward. I used flat head screwdriver to help disconnect the connection.
Also, to help getting the old icemaker removed. Once removed returned New one the reverse of taking it out. Won't need screwdriver to get it back in place. Put cover back in place and put the Phillips screw back in place. Plug refrig. back in. put it back in place turn the water back on should be good to go! BE afew hrs. before ice starts to show up!
Good Luck

Moved stuff out of my way on the top shelf, reached in and turned old filter to remove. Filled new filter with water, lined up and turned to lock in place. Whew, never thought I would get that job done. :-)

Took out the old piece. Washed and replaced with the new one.

Water flow restrictions. Replaced flow valve. No help. Checked again and found filter head flow stopping valve broken. Replaced same. All good.

Took the old filter out and put the new one in.
Easy Breezy!!

TOOLS NEEDED ARE A #2 PHILLIPS, A FLAT TIP SCREWDRIVER AND SOAP AND WATER FOR CLEANING OF THE VEGETABLE PAN COVER.

1. REMOVE BOTH VEGETABLE PANS.
2. REMOVE THE VEGETABLE PAN COVER BY SLIDING IT FORWARD ENOUGH TO BE ABLE TO LIFT IT UP AND OUT.
3. USING THE PHILLIPS SCREWDRIVER REMOVE THE 2 SCREWS HOLDING THE RAIL TO THE CASE.
4. IF THE REAR PART OF THE RAIL IS BROKED OFF AND STILL IN THE WALL OF THE FRIDGE (LIKE MINE WAS) REMOVE IT WITH THE FLAT TIP SCREWDRIVER BY PRYING IT OUT OF THE SQUARE HOLE . USE SOME PRESSURE IF NEEDED.
5. INSERT THE REAR PART OF THE RAIL (LOOKS LIKE A LANCE) AND PUSH IT IN ALL THE WAY TILL IT STOPS.
6. THE PHILLIPS SCREWDRIVER ANCHOR THE RAIL TO THE WALL OF THE FRIDGE FIRMLY, NOT TOO TIGHT.
7. USING THE SOAP AND WATER, CLEAN INSIDE OF THE FRIDGE AND ALL PARTS REMOVED.
8. LAY THE VEGETABLE PAN COVER ON TOP OF THE RAILS AND SLIDE IT BACK TO LOCK IN PLACE.
9. INSTALL THE VEGETABLE PANS.
10. WORKED FINE, LOOKS FINE AND LASTS A LONG TIME.

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

Took out Philip’s screw. Applied heat from hand hair dryer for one minute. Unplugged wire plug. Pushed ice maker lever to release and gently pulled forward.Removed old ice maker and replaced with a new maker.
Plugged in wire harness and replaced wire cover.

Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Easy

got new filter