DE412 Maytag Dryer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum Support Roller Kit – Part Number: 12001541
$33.28
In Stock
Drum Support Roller Kit
★★★★★
★★★★★
(74)
Part #12001541
This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once.
Tumbler and Motor Belt – Part Number: WPY312959
$37.35
In Stock
Tumbler and Motor Belt
★★★★★
★★★★★
(63)
Part #WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in color and it is made entirely of rubber. If your dryer will not tumble, is noisy during operation, or will not start you may need to replace the belt. To complete this repair, you will need to remove the front panel as well as the drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver to complete the repair. Be sure to disconnect power to the dryer before you begin this repair. During the repair, make sure the belt doesn't fall into the groove in the drum, which will cause it to be too loose. You should be able to access the belt and replace it by removing the front panel and bulkhead.
Roller Shaft – Part Number: WP6-3129480
No Longer Available
Roller Shaft
★★★★★
★★★★★
(1)
Part #WP6-3129480
This roller shaft is the axle for the drum roller, also known as drum roller axle.
Front Glide Kit – Part Number: 306508
$19.14
In Stock
Front Glide Kit
★★★★★
★★★★★
(16)
Part #306508
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
Blower Wheel with Clamp – Part Number: Y303836
$32.26
On Order
Blower Wheel with Clamp
★★★★★
★★★★★
(59)
Part #Y303836
This blower wheel comes with a metallic hub clamp to hold it firmly in place.
Lint Filter – Part Number: WP33001003
$42.36
In Stock
Lint Filter
★★★★★
★★★★★
(60)
Part #WP33001003
This lint filter screen is slide in styl type of Maytag filter screen. It is most typically used for the 08 and later series of Maytag gas or electric clothes dryers that appear before 1990.
Dryer Retaining Ring – Part Number: WP9703438
$12.00
In Stock
Dryer Retaining Ring
★★★★★
★★★★★
(3)
Part #WP9703438
This metallic retaining ring is less than an inch in diameter. It is made entirely of metal.
Drum Roller Shaft Washer – Part Number: WP312535
$18.41
In Stock
Drum Roller Shaft Washer
Part #WP312535
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
Idler Pulley Wheel – Part Number: WP6-3037050
$25.19
In Stock
Idler Pulley Wheel
★★★★★
★★★★★
(4)
Part #WP6-3037050
This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.
Front or Rear Drum Felt Seal – Part Number: WP314820
$35.15
In Stock
Front or Rear Drum Felt Seal
★★★★★
★★★★★
(2)
Part #WP314820
This front or rear dryer drum felt seal is seventy-nine and a half inches long.
Idler Pulley Shaft Washer – Part Number: WPY312527
$18.52
In Stock
Idler Pulley Shaft Washer
★★★★★
★★★★★
(2)
Part #WPY312527
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
Door Latch Kit – Part Number: 306436
$13.84
In Stock
Door Latch Kit
★★★★★
★★★★★
(13)
Part #306436
This dryer door latch kit comes in two pieces: a door latch, and a door strike. It's used to help hold your door shut to your dryer.

Questions And Answers for DE412

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Felix - For model number DE412
January 25, 2022
How can I get to the belt ?
Chris Boyle Profile
Hello Felix, thank you for the question. We have attached a video on replacing the Belt. We hope this helps!
$37.35
In Stock
Tumbler and Motor Belt
5 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Ramon Jasso - For model number DE412
February 21, 2020
Starts and heats but tumbler will not turn. I think it needs the belt..ps11757542 .$17.26.but not certain to order or not
Chris Boyle Profile
Hello Ramon, thank you for your question. The most common cause of a dryer that will not tumble is a broken belt, which is Tumbler and Motor Belt Part Number: WPY312959. Good luck with your repair!
$37.35
In Stock
Tumbler and Motor Belt
2 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Peggy - For model number DE412
September 3, 2021
Have replaced heater & other parts regarding dryer not working, dryer will only heat for 15 minutes. Could it be the timer?
Chris Boyle Profile
Hello Peggy, Thank you for the question. If all three Thermostats and the Thermal Fuse have been tested or replaced along with the heater, the Timer could be defective. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
$52.75
In Stock
High Limit Thermostat (Limit: 200-30)
$92.28
In Stock
High Limit Thermostat
$431.98
In Stock
Dryer Timer
$45.09
In Stock
Thermal Fuse (Limit: 183)
$79.91
Special Order
Dryer Cycling Thermostat
Was this helpful?
Thank you for voting!
Bev - For model number DE412
February 24, 2022
Need parts number for the lint filter cavity wall that is a plastic grid.
Chris Boyle Profile
Hello Bev, thank you for writing. The part you are requesting on has been discontinued and we have no known replacement listed in our system. We have no further information. You are welcome to contact the manufacturer of the part to see if they have recently released a new substitute. Good luck with your repair.
Was this helpful?
Thank you for voting!
Russ - For model number DE412
January 13, 2023
Dryer will only run if I keep the start button depressed. What part do I need to make it run.
Chris Boyle Profile
Hi Russ, thank you for reaching out. The issue seems to be with the Door Switch, we would recommend checking it as it may become faulty, the part number is PS1964648. If that does not help, we would recommend checking the Thermal Fuse, part number PS11740678. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
$39.55
In Stock
Door Switch Kit
$45.09
In Stock
Thermal Fuse (Limit: 183)
Was this helpful?
Thank you for voting!
  • 1
  • 2

Common Symptoms of the DE412

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
noisy rollers, broken latch
673 of 705 people found this instruction helpful.
  • gerry from west covina,, CA
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable), Wrench set
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of t he front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.
Was this helpful?
Thank you for voting!
The blower fan (nylon) stripped off the motor shaft (steel)
574 of 583 people found this instruction helpful.
  • Stephen from Lafayette, IN
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Was this helpful?
Thank you for voting!
electric dryer was rumbling - wheel or belt?
602 of 711 people found this instruction helpful.
  • Raymond from West Bend, WI
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through . Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.
Was this helpful?
Thank you for voting!