DDW361RAC-PDDW361RAC0 Amana Dishwasher - Instructions

Actual i missed diagnosed the leak and ordered a very expensive door gasket. The leak was coming from shrinage of the wax resevoire o rig and the tab seal for the soap dispensor. I missed the trees the forest got in the way. The leak was dripping alond the front panel well away from the main door seal.

I cleans a the plastic surfaces and noticed a lip around the opening for the reservoire and used 150 sandpaper to remove it. Replaced the O ring, tab seal and bothe selonoids and cleaned everything. Put it back together. Works find lasts along time

First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

Sooooooooo, I ordered a new kick plate, it arrived promptly, tried installing it and it was being difficult. Removed plate above that and lined up new plate(kick plate) tried putting plate above it on and as when we installed the machine that upper plate was difficult. Removed upper plate to fcheck problem of installation and guess what? Stuck in the inside of the upper plate was the lower plate complete with sound insulation. Happy ending :-)

First unplug the unit. Open door. Take a special tool to remove all the screws (star shaped) around the edge of the door, and remove plastic panel where motor for detergent cup sits. Remove wires (two) from the motor. Remove wax motor by unsnapping motor from its cradle--comes out by moving the fingers holding it in. Push new motor into position, being sure the round pin sticking out at the end (on the left side) so that it sits in the groove made for it. Replace panel and screws, plug power cable back into its box. Close detergent cup door, turm on dishwasher, run through cycle, open door and check to see if detergent door opened up. If it did, then fill with dishes and wash.

First, I searched the repair help on this site to see what others did to repair their diswashers, and it looked easy, so I just followed the same instructions. First, I used a hex star key wrench to remove the screws that hold in the interior door cover. I disconnected the leads to the defective wax motor, reconnected the leads to the new motor and screwed the door back together. It took 15-20 minutes and was a piece of cake! My first appliance repair, and as a single woman and first-time homeowner, I was really impressed with this site! It gave me confidence to tackle more home repairs instead of calling for service and getting raked over the coals.

1) Emptied Dishwasher (roll-around model)
2) Tipped it onto its back
3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver)
4) Opened Door to access side panel (careful not to let it drop on my fingers)
5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring.
6) Removed broken link
7) Installed new link and spring noting the spring direction from the spring on the other side of the door.
8) Pulled spring over the bottom rail bracket with pliers.
9) Reinstalled panels in the reverse order.

First, I removed the screws that hold the interior part of the door in place. Next, I removed the two screws that covers the interior parts of the latch release in place. Then, I removed the broken latch, put in the new one and attached the spring. I put the pieces back in place, and the two screws back in. Finally, I screwed the door panel back together.

first I turned off the water to the dishwasher, and turned the power off for the dishwasher.
removed the 4 screws from bottom panel
then removed the 2 screws from the bottom of the counter,
at this point I could pull the dishwasher out. then figured out where the part went and attached.
pushed the dishwasher back and lined up the holes under the counter, put those in first, the put the bottom panel back on, turned the water back on, and flipped the breaker switch.
Reading the other stories really did help me get some idea of what needed to be done

Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer

Very easy after watching the video. thanks

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.

I recieved a different part than was in the picture and description that I ordered, and was billed twice for it. I wasn't able to fix my dishwasher

Simply had to replace the clips in the correct position. Would have been a five minute job if I had noticed which way around the old parts went before removing them from the dishwasher to find replacements. It's amazing hoe many permutations there were before it all fit together perfectly.