DDC0580BAL General Electric Dryer - Instructions

open the front of the dryer, open the back access panel, remove the old belt fragment, pull front cover away from bushing surface at the front of drum, drape new belt around the face of drum, match location visible as the track of old belt, reroute belt at the motor and install tensioner in the proper way, reattach front cover, install back panel, done.

Just put it in place. The hardest part was to choose the model number closest to the one I have (since it wasn't listed). PartSelect.com showed a list of similar models and I was able to choose from that. Luckily I got the right one (wrong color, but it fit!).

There were no tools required. I simply pulled out the old filter, compared it to the new filter, for size and shape. Then simply placed the new lint filter in place of the old one.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

Followed an online website, removed the top, front, two rear access panels, disassembled the spring clip from the rear of the drum, took the belt off of the motor, removed the drum, took the rear bearing support out, replaced the bearing and reassembled the dryer.

The repair was simple with my mechanic relative handling the tools. Total time about 25 minutes.

Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.

replaced rear drum bearing kit Still makes the same noise

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

First I checked on-line "how to change a dryer belt" and followed the instructions. Remove front panel and slide belt over drum, in the back, put belt around pulley and hand trun the drum. on-line instructions had pictures to ensure proper install. It was easy.

Unplugged machine and turned off the gas. Removed top panel,4 screws along inside top edge of door opening. Used a wooden shim to pry the drum away from the surrounding "lip with felt padding. Slipped belt through.the trick is getting the belto around the entire drum. First I got it over the top of the drum, and fed it around the bottom by turning the drum and pushing the belt through the opening made by the shim between the bottom of drum and the lip with felt. It was kind of like feeding a bicycle chain onto a sprocket as you turn the wheel..
Removed back panel and vent hose, removed old belt laying on floor of machine, fed the belt onto the motor pulley and the tension pulley. Tension pulley presses on top side of belt. Belt should be in same position on drum as old belt, you can see a friction mark all around the drum from the old belt.
Replaced panels and vent hose. Put felt padding back into place wherever it slipped out. Very important because if you don't it scrapes the drum when turned on and makes a loud sound.
Dryer works perfectly again.

First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).

Just removed old tray and installed new tray.

I was completely surprised that in less than 24 hours the new part was at my door!
This is the kind of service every company should strive to supply to the customer,and the delivery fee was regular 3-5 day delivery.
A job well done !!!!

1. Open dryer door.
2. Remove old lint filter.
3. Put new filter in it's place.

Removed old lint filter and replaced with new one. Was impressed with the fast delivery.

nd removed it from the unit.
5. replaced drum bearings
6. reassembled everything in the same order I took it off.

Be sure to mark any wires you may disconnect to ensure you connect them back correctly.
Was a bit frustrating at times, but made it through and there is no more squeek.