DDB1501AWZ Admiral Dishwasher - Instructions

Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.

Removed the inter door panel replaced broken handle put panel back washed dishes

I removed flowplate assembly, chopper assembly, found that the plastic spindle was stripped causing arm not to spin. In the new seal kit, the spindle was made of metal (much better design). I replaced the spindle, chopper, and filter assembly (old one was caked full of gunk). Worked like a charm. A previous post helped me figure out the problem.

First I shut off the water and electricity to the dishwasher. I removed the screws holding it in the cabinet and pulled the dishwasher out. Disconnect the water line and turn the unit face down on the floor. I disconnected the wire harness by pulling it out. It was a little hard to pull out. Then I removed the screws holding the pump in place, then removed the pump. I inserted the new pump and replaced the screws, and the wire harness. Then stand the unit upright, reconnect the water line (use teflon tape to prevent water leakage), put the dishwasher back in the cabinet, and restore power and water. Then you're done. It would have been very simple if I had used teflon tape the first time. I had a leak the first time I reconnected the unit and had to take it out again and apply the teflon tape. After that, everything was fine. The dishwasher works great.

PartSelect web-page for this model listed the handle as the most often ordered part. It arrived the next day after the order. It was necessary to remove about a dozen Torx screws to remove the back from the door. The power was turned off at the breaker. Two electrical fittings were removed from the broken handle and placed on the new one, and the part was put into position and the door back screws reinserted. I was fortunate to have the appropriate Torx driver and suggest that PartSelect offer such an unusual tool with the part.

You just remove the old unit and set in the new unit. the wheels were already connected.

Very easy after watching the video. thanks

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Shut off the electricity to the dishwasher. I removed all 11 screws from the door panel. After separating the 2 door panels, I removed the 2 door switches from the door handle ( I used a flat head screw driver to help get them out). Then I unplugged the 2 switches and plugged in the new ones. I replaced the door switches into the door handle ( this was not an exact fit because the new switches is slightly larger than the old ones). I put the new switches in place as tight as I could in the handle. I screwed the 2 screws holding the handle first to secure it before I put all the other screws in the door panel. I turned the electricity to the dishwasher back on. Our dishwasher has been working perfect ever since then and it is over 10 years old.

1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order

No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.

Pulled out the old one and put in the new one!

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

replaced rack

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.