DDB1501AWB Admiral Dishwasher - Instructions

Open front removed all the star screws. Took the old switch unplugged the wiring one at a time to put on new switches. Placed the new switch back and installed all screws. Using a drill with the star tool made it go faster. Total time 9 mins

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were re ... Read more placed and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!

I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and th ... Read more ey warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.

replaced rack

Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.

Took out 11 stainless screws that hold in inside door panel, pulled out latch assembly. The only reason the repair took as long as it did, had a hard time pulling the contacts out of the wire harness, I was terrified that I would break the plastic plugs. This dishwasher is probably 20 years old or older and plastic gets really brittle wit ... Read more h age. The left side came out a little easier than the right one. When I got brave and tugged harder I managed to break the offset contact inside of the plug. Just gave it one desperate powerful tug wit my pliers and out it came, thank goodness the plug itself wasn't damaged. Put assembly in place, ligned up the screw holes in the door panel, put screws back. Works like a charm. The black color of the handle does not perturb me, It is recessed and only shows when dishwasher is running. By the way I'm a 75 year old female and am rather proud of myself. Lol

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).

First, I had to purchase a small socket set that had the piece needed to remove the screws from the inside panel of the dishwasher. I didn't cost much. After removing the screws, I disconnected the old door latch/handle, but had to leave the old leads in place because I couldn't remove them. I replaced the old latch/handle with the new on ... Read more e, replaced the inside panel, and tried it out. The new latch/handle worked great. The replacement time was under 20 minutes (struggling with the old leads). Very happy with the outcome, though.

Thanks.

Luckily the door opened one last time. Remove torx screws on the inside. Spread panel open to gain access to handle. Removed handle because it's already loose from removing torx screws for panel. Electrical wire connectors were extremely tight. Used pliers to remove connections there are 2.
Reverse procedure for installation.

Removed inside door panel, handle assembly was then free to move. Unpluged both switches attached to handle assembly. Plugged in new switches and positioned new handle assembly. Replaced inside door panel and screwed into place. Closed door. it works. job done.

1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx s ... Read more crew)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order

I simply went on line and found a video tutorial which explained the process.

Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer

MAKE SURE ELECTRICITY TO DISHWASHER IS OFF!!! If dishwasher is installed directly wired, TURN OFF THE BREAKER!!! Undo the inside plastic door molding....remove the old latch and install the new one! Easy to install! Wife is very happy!