DCXH46EA1WW General Electric Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer had a bad sqeaking sound
First I like fixing things for myself. So I looked the problem up on the internet. Found the repair tech that I needed. The found your parts site. And BOOM. Looked up mt part on your site. Very easy you had everything I needed. And you got it to me quick. THANKS. When the part hit my mailbox. Everything I needed was there. I pulled the plug. Fliped the lid up. Took off the front. Removed belt off the ideler. Removed drum replaced bearing assy. Put it back together. Closed the lid and pluged the unit in. Worked so well I felt like a pro. My wife was tickled pink. Just like a new one. Thanks guys for making me look good and saving me a lot of money. Will use this site again. I give you 2 thumbs up.
Parts Used:
-
james from mascotte, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Started with an annoying squeaking noise until the shaft broke and the drum hit the floor, KTHUD!!
I ordered the rear drum assembly on Monday evening and the part came on Wed at 11 am. I started the repair at 1 and finished at 3. It would have been faster, but my computer kept freezing during the repair video. The video was so easy to follow. I could have used longer arms or a helper, but I managed to get the job done by myself. Needless to say, my husband was thrilled. Great service. Thanks
Parts Used:
-
Cheryl from Tulare, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rear bearing was squeaking
Repair went just according to the video except to pull the drum out there was a plastic lock at the front of the dryer. It was held in by one screw and easy to take off. When I pulled the drum out the armature and spring that hold the belt tight fell off. I panicked a little, but easily put the pieces back in place. When I started the dryer for the first time it sounded odd but realized it was the sound of all the grease spreading itself around the bearing.
Parts Used:
-
Robin from Lafayette, OR
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
A loud squeeling sound
Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.
Parts Used:
-
Delbert from Grass Valley, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
loud metal on metal noise
Replaced rear bearing on back of dryer. Repair cost $20.00 an a little time. Much better then buying a new dryer. It was easy to repair the video instructions were great. I would do it again it needed.
Parts Used:
-
richard from orchard beach, MD
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer Squeaking
Found instructions on "UTube"some of the screws were in a different position but you can see them. While you have the dryer apart it's a great time to clean it and also as long as you've gone this far replace the belt,it's probably time.
Parts Used:
-
Gilbert from Elizabethtown, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer making scrubbing noise while running
This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.
Parts Used:
-
David from Raven, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
banging noise
-
gordon from creve coeur, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Loud squealing noise until dryer heated up - then quiet
-
Ernest from Stockholm, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The Rear drum bearing kit had sheared off
Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!
Parts Used:
-
Amy from salem, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rear drum bearing failure
Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''
Parts Used:
-
TonyMac from Alamo, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum
I remove the drum, and install the bearing just like the instructions in the video.
Parts Used:
-
Witly from Wheatley Heights, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!