DBL333GY0WW General Electric Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Start knob on dryer broken
There really is not much to explain, the new knob was so simple to replace that my six year old could have done it. No tools were required and it took less than a minute to replace the new knob.
Parts Used:
-
Jessica from Spanaway, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum Guide And Seal Wore Out
Lifted top and removed front panel and cleaned old glue off. Put new glue on put seal used spring loaded cloth pins to hold till glue dried
Parts Used:
-
GARY from SPRING VALLEY, MN
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
On knob was broken
-
Roy W from Albany, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Terrible squeaking sound
Squeaking was coming from the back of the drum, not the glides. The hardest part was trying to figure out how to pull the drum out. With a little extra tug, the back pin of the drum lifted out of the socket. That was the cause of the sqeak. Just cleaned it up and added some grease and good as new. I noticed the front glides were worn and replaced it.
Parts Used:
-
Michael from Shrewsbury, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob was broken off ordered a new knob.
First the old knob was broken just pulled it off. made sure the metal piece was clean of all debris or junk and slide the new know on turned it to make sure it was snug and was ready to go. to easy
Parts Used:
-
starla from Fort Cambell, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bdryer broken knob
I just put the new knob where the old one was and presto it was done. The whole process was much easier than I expected.
Parts Used:
-
Julie from Portland, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Start knob was broken off flush with switch
I turned off the power, unscrewed the 4 screws from the top of the dryer. I then opened it and turned the switch that was in there counterclockwise exactly as utube video said to do. I then took off the two wires from the old switch. The rotary start switch fix right in where the old one was. I put the panel back together, put on the old knob and turned the power back on! It took less than 15 minutes from start to finish! If I can do it anyone can! Joanne Klinkhammer Cecil, Wisconsin
Parts Used:
-
Joanne from Cecil, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
start knob replacement
-
al from Cathedral City, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob broke
-
Janis from northridge, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My husband broke the start knob, because he didn't know that you have to select the time and fabric selection first
-
Joanne from LaQuinta, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would not start
-
Leroy from Charleston, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
stripped knob on dryer
-
Sarah from Roswell, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
knob pastic insides broke
-
Barbara from Hawley, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dry would not work, knobs were stripped and did not turn properly.
Yes, we should have done this a long time ago and put off replacing the starter knob and heat adjuster knob. By the time they no longer worked, we called in an expensive repairman. When we realized what the problem was, we thanked him, paid him lots of money and did what we should have all along - replaced the knobs throug partsselect.com instead of using the repairman for another $150.00.
We received the knobs within 3 days (paying for medium fast delivery was worth it) and simply pulled the old problem knobs off and put the other ones on. Simple, no brainer work.
Save yourself expensive repairs and replace those knobs when they start going. Also, when you test the machine, make sure you turn the setting to a time (stupid mistake that most of us do) to make sure that the knobs work properly.
Good luck. A terrific experience with Partselect.com. Would use again in the future and recommend to others.
We received the knobs within 3 days (paying for medium fast delivery was worth it) and simply pulled the old problem knobs off and put the other ones on. Simple, no brainer work.
Save yourself expensive repairs and replace those knobs when they start going. Also, when you test the machine, make sure you turn the setting to a time (stupid mistake that most of us do) to make sure that the knobs work properly.
Good luck. A terrific experience with Partselect.com. Would use again in the future and recommend to others.
Parts Used:
-
Danielle from Chatham, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
backet seteled and belt spined arround without going traction
-
Yuriy from West Springfield, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!