D1475TUR1 LG Dishwasher - Instructions

Removed mounting screws from sides of disher. Removed broken piece of connector assy still attached to hinge. Attached new connector assy to hinge then looped it around pulley with spring attached to opposite end. Need both hands to pull spring up to side of tub and connect it. I would suggest replacing both connector assemblies while you have the dishwasher pulled out. Push dishwasher back in and mount with screws.

Replacing the spring and connector assembly (the cord had frayed and broken) was easy and took only a matter of minutes to do. Wrestling the dishwasher in and out of its space under the counter was very difficult. Because my kitchen is compact, I had to move the refrigerator first, then disconnect the Romex cable and water lines from the dishwasher before I could pull it fully from under the counter. The side panels have screws in the front and the back, so the appliance had to be moved out until its back was exposed. But I got the job done and the door works just like a new one now!

Pull the dishwasher out from underneath the countertop took 2 minutes unscrewed the panel on the side one minute put the connector on one minute screwed the panel back on 1 minute put the dishwasher back underneath the counter two minutes very easy job

Snapped the rollers on.

Unscrew all screws on the inside of the dishwasher door. Carefully separate the front panel from the inside panel. Lift out the latch assembly, remove connectors from both sides using needle nose pliers. Reconnect to new assembly and situate back into place. Close front and inside panel, replace all screws, making sure the short and long screws go back to where they came from. Quick easy project to eliminate 2 trips from a repairman, 1 for the diagnosis and 1 to do the work!

Had to call have an installer attach a metal strip across granite counter top and they did not have the top mount brackets so I had to order them and finish the install. The dishwasher was installed on the side mounts and they missed the cabinets

The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door.

I am 77 years old and got it all on but the corners did not want to go in so I had to call my grandson and he got them in. It still leaked on the bottom left side. It is getting old (11 yrs) so I decided to get a new one. It is actually pretty simple to install, but it does take a little strength.

Took out old rack. Put in new rack. Done.

No other assembly required.

pulled dishwasher out of cabinet, removed side panel held by screws front and back, removed broken tension rope installed new rope, replaced side panel pushed dishwasher back into cabinet and fastened
to countertop, door works like new now, (the chief cook is happy as she can be)

My husband was able to slide the dishwasher out, and quickly replace the old connector assembly for the new ones. The old connector assembly had broken at the “rope”. Now the door opens slowly and is as good as new.

The repair took right at one hour. Repair length of time will depend on what all you have to disconnect to get your dish washer out so you can remove both side panels where you will be able to access the door springs, etc. There is a door spring on each side and I recommend replacing both connectors cords while you have the dishwasher out. Mine were both broken. One thing I noticed when doing my repair was that the bracket that is on the bottom of the door was not aligned properly to the small pulley that the connector cords travels under. If yours is out of alignment you will be able to tell once you get the connector cord installed. I used heavy pliers to bend the bracket slightly inward so the connector cords rides in the center of the pulley and not off to the outside as before. This may be why mine broke in the first place. After part replacement, reinstall the door panels and put the washer back in service. There are also YouTube's of this repair so you can see what you are getting into. Basic repair.

Took off the broken one and snap on the new one.

snapped on new axel-wheel assembly

Replaced it . Simple