CWE4800ACS14 Maytag Wall Oven - Instructions

Unscrewed two screws, unplugged two small plugs, plugged the new ones in and screwed the screws back in. Less than 10 minutes.

Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.

put the old one out,put new part in that easy,works like new

Very simple. Removed two screws-pulled element out about 3-4 inches-pulled off the contacts-reversed procedure using the provided screws, turned the breaker switch on and everything worked fine. Excellent service from parts select and quick shipping.

I unscrewed the old element from the back of the oven. Then I detached the wires and took the old heating element out. I then fit the wires into the new element and screwed it back in using the new screws. It was really easy! I was lucky to have my father in law show me how, since this was my first time to do it.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Turned breaker off. Took out two screws holding it in place. Disconnected two wires. Put new element in. Works fine

Turned off the circuit breaker. Removed the oven door from hinges. unscrewed the old element connection plate. Pulled off two wire leads. Reversed forward steps to completion.

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

Loosened the two screws holding the element, pulled the element out of the back of the oven, loosed the two wire leads connected to the back of the element, removed the broken part, placed the new element into the oven, reconnected the wire leads, pushed them back into the insulation in the back of the oven, repositioned the element into its place and replaced the two screws holding it into place with the new screws that came with the new part. Oven element fired right up first try without any further complications. One of the easiest appliance fixes I have ever done!

turned off power unscrewed plate that held in element unplugged socket from old element plugged in new one screwed plate back turned on power works fine

First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.

Removed two screws on sensor in the oven. Pulled out stove and after unplugging same removed the back panel. Sensor has an electric connection on the rear of the oven with a connection that is easily separated. Threaded new sensor electrical connection through inside of oven and connected on the back of stove. Pushed insulation back around the wire were in goes through to the oven. Replaced back on stove and screwed in two screws which hold sensor inside the oven. Replaced back cover on stove, plugged it in and pushed it back in place. Did the trick for me..

I found the oven model #, and ordered a control module from Part Select. Rcvd the part a few days later, carefully installed and wired it in place like the old one. Well, to my surprise, it did not work. So, I called Part Select, ordered another and I will return the defective part for credit. The second module was rcvd, installed and works just fine. The two reps I spoke from Part Select were very professional and helpful. I am hoping I will receive credit for the defective part as they said they would. Al

Removed the two screws on both elements, pulled the wires off, put the wires on the new elements and put the screws back in. Very easy, works perfect.