CVE3401Q Jenn-Air Cooktop - Instructions

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Looked up the part on the internet. Found it with ease. The thing I did miss was that the switch had a small nub to keep it in the right place in the Glass top. The repair went easy. Probably took no more than 15 minutes. I would use PartSelect again.

Remove the connectors (ID where it goes on the new item). Unscrew the two screws and remove the broken radiant filaments. Install and screw the new radiant filaments; then, connect back the connectors to it's proper connections.

The old grease filter was removed and the entire downdraft was cleaned. The new filter was slipped in. It is so nice to have the old one out. I am so appreciative of finding this part. :-)

Knocked breaker removed stove top from iland removed a dozen screws replaced switch put screws back in installed top back in iland put breaker back in worked purfect.

Removed the cook top from the counter. Removed the switch housing and then the switch. Found a match and ordered. Part came in 2 business days. Once I put together the housing and connected the wire housing the burner worked perfect. The downdraft fan remained on. Placed a call to Jenn Air service and was asked to disconnect the fan switch. There must be some memory in the solid state portion of the switch. After a few mins I replaced the fan switch and hooked up the wiring. All worked fine.

turned off power to stove top..lifted unit out unscrewed top and switch had 2 screws re-placed switch and put back together.. make easy $100 plus switch

The dual burner on my range wasn't working—the inner, smaller portion would heat up, but the outer portion (for larger pots/pans) would not. I searched online and discovered that the element is easily replaced, and Yay! It was! I had difficulty finding the model number of my range, as it wasn't in any of the obvious, suggested places. I had to get help to slide my range away from the wall (which was the most difficult part of this project!), but in doing so, found a metal tab on the back of the range, near the top, that flipped up to reveal the model and serial #s! From that info, I was able to find and order the correct replacement element for the burner that wasn't working, and in less than an hour, had it fixed!

I removed the glass top and replaced the switch unit successfully. Hardest part was removing the unit from the countertop and bracing the base with a 4x4.

verified that the heating element was at fault by measuring it with ohmmeter. There are 3 contacts on the outside of the element. Resistance between center contact and either outside contact should read something close to 0 ohm, if it is good, and if it is burned, it will read open circuit (infinite resistance). Wanted to make sure that this is not the switch, which I replaced a few months ago. Before I disconnected all the connectors from the element I made picture of all the connections, just in case I forgot what gets connected to what (didn't use it, though). Installing the new element was very easy. Most work is done getting access to the element. Repair went smoothly, range works fine, now.

Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.

the filter fit because the scale in the photo allowed me to choose which one to buy!

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

Took the old filter out and put a new one in. No tools no fuss no muss. Very easy.

The repairs was really easy. All you had to do was remove the screws holding the glass top surface down, raise it up, then start by pulling one wire at the time and plugging it into the new element. Then bolt the glass top surface down and it was ready to use, good as new.