CTH14CYBRLWW Hotpoint Refrigerator - Instructions

I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !

At this time of the year our beach fridge is always full of food and drinks. Every time we want something it meant leaving the door open for extended time whlie moving things left, right and center. When the new shelf arrived I removed the food and drinks from the existing two shelves and moved them closer together. I then slipped in the new shelf and reloaded the food. Suffice to say the fridge stays open less and we are able to get at things without moving others. I wish I had thought to do this before.

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

Removed plastic covers and used a nut driver to remove the two screws that held the heater assembly to the freezer coils, disconnected wires from old assembly, connected wires to new assembly, replaced mounting screws and replaced plastic covers and secured them with the original screws. All in all, a fairly easy operation.

Remove the fridge door and put it on the floor. Being able to apply lots of pressure helped get it into the tight groove. The corners were the hardest part. This requires strong "man" hands!

took out 4 screws - lowered timer cover - replaced timer- put it back together

Easy fix - snapped together.

Removed frozen items, lined up the holes at an angle and put the exposes splines in the holes provided in the sidewalls of the freezer.

From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.

Wow, end result was amazing. I had to place my ear close to the refrigerator to find out if the fan was working. So quiet. Prior to this we could hear it in the bedroom. I replaced the fan motor, blade, grommets, i.e. the whole fan train. There were two screws holding the fan which were removed. (After removing the back panel.) Then removed the old blade and dust cap. Detached the wiring harness at the junction. Then reassemble in the reverse order. I screwed up the 1st time...installed the front motor grommet in reverse. Fan blade was not centered. Resulted in a few mins rework. Actually spent more time cleaning all the dust from the compartment and behind the refer than it took to install the new fan system. Did I say that I couldn't be more pleased with the no noise result?

I haven’t received the wheel yet. Originally ordered on Dec. 13. Hadn’t received it by Dec. 20. Finally shipped on Dec. 22. Tracking said it was expected to be delivered on Jan.2. Not delivered. Then it said it was still on its way but it was unknown when it would be delivered. Still waiting on Jan. 6. By far the most expensive economy shipping ever, as this refrigerator is in a rental that can’t be rented until a wheel is installed.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Shelf cracked when less than year old. and has gotten progressively worse thru the years.
Replaced in seconds , no tools required .
I should have done this years ago

Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...

The parts came the next day after ordering and I didn't pay for fast shipping. I removed the drawers and the old lid-shelf and replaced it with the new one; also added an extra shelf. I love the new items and they fit perfectly.