Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Not making ice, and water leaking in freezer
2 of 2 peoplefound this instruction helpful.
Raymond from Northglenn, CO
Really Easy
Less than 15 mins
Screw drivers
Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness
Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on
ALL FIXED!
Was this helpful?
Thank you for voting!
damaged trim and retainer bars
4 of 8 peoplefound this instruction helpful.
Stephen D from Newport Beach, CA
Really Easy
Less than 15 mins
Replaced parts. PartSelect service, web site, telephone discussion, and response time all truly remarkably excellent.
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Icemaker made some pretty sad cubes! Hollow, unfilled, or small cubes
2 of 2 peoplefound this instruction helpful.
Dana from ABINGTON, PA
Easy
30 - 60 mins
Nutdriver, Screw drivers
Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.
Was this helpful?
Thank you for voting!
Compressor would short cycle after overload tripped
2 of 2 peoplefound this instruction helpful.
Eric from VALLONIA, IN
Really Easy
30 - 60 mins
Pliers, Screw drivers
Test original overload with meter to see if voltage drops out when overload trips. It did. Measured amp draw to verify compressor load was with in range, it was. New overload no longer trips during compressor start up.
Was this helpful?
Thank you for voting!
water leaking into ice tray, frozen glob of ice
2 of 2 peoplefound this instruction helpful.
james from newfield, NJ
Easy
30 - 60 mins
Screw drivers
installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.
Was this helpful?
Thank you for voting!
My ice maker went out, I decided to replace the single outlet water valve as well.
2 of 2 peoplefound this instruction helpful.
Patricia from Pearland, TX
Easy
30 - 60 mins
Nutdriver, Screw drivers, Wrench (Adjustable)
removed the cover from the back of the refrigerator, and used the nutdriver to loosen screw on the single outlet water valve, removed the old water valve and the hoses to it. Connected the hoses to the new valve and attached to the wall of the refrigerator by tightening the screw. Then removed the old ice maker from the inside of the refr
... Read moreigerator, by loosening the two screws and attached the new one, I tightened the screws and then I was done. It is working great.
I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.
... Read more
The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)
After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.
Read less
Was this helpful?
Thank you for voting!
The support had broken and the shelf was just hanging there.
2 of 3 peoplefound this instruction helpful.
Deanie from Amarillo, TX
A Bit Difficult
Less than 15 mins
Screw drivers
I unscrewed the support and replaced it with one that I ordered. It was fast and easy.
Was this helpful?
Thank you for voting!
Replaced Ice Maker
2 of 3 peoplefound this instruction helpful.
Steven from Clinton Corners, NY
Easy
Less than 15 mins
Nutdriver
Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.
Was this helpful?
Thank you for voting!
Ice Maker Leaked Creating an Ice block
2 of 3 peoplefound this instruction helpful.
Loren from Indianapolis, IN
Really Easy
Less than 15 mins
Screw drivers
Merely remove the front bottom screw that attached the ice maker to the refrigerator Lift the ice maker gently off of the 2 top screws Unplug the icemaker wiring harness from the back of the refrigerator, and remove Snap off the end of the maker and remove the keeper for the wire arm Remove the wire arm and install on
... Read morenew maker Unplug the wiring harness from the old maker and plug into the new one Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker Install bottom screw into the bracket that holds it in place. This took less than 5 minutes.
Read less
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 peoplefound this instruction helpful.
Gail from Golden, CO
Really Easy
Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
Broke The Shelf
3 of 6 peoplefound this instruction helpful.
Heather from Allentown, PA
Really Easy
Less than 15 mins
Oops! While cleaning this in the sink, I shattered the glass shelf. It was so easy to order the piece and it came in record time! Out of the box, quick wipe down and into the fridge. Couldn't have been easier.
Was this helpful?
Thank you for voting!
The bottom brackets on the inner door were missing.
2 of 3 peoplefound this instruction helpful.
Linda from Saginaw, MI
Really Easy
Less than 15 mins
The frig had broken brackets on the inner door. I connected the clips to the trim piece and I snapped the entire piece into the slots on the door. Presto! All finished.
My Orders
