CSG9900AAE Maytag Cooktop - Instructions

Michael from Mountain Iron, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Worn out stove top

We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!

Parts Used:

Redona from Roseville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

simple swapping of parts

Undid the bad part and installed the new one

Parts Used:

lenny from east freetown, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Burner wouldn't light.

Took out a couple of screws and put in the new part. PartSelect was fast and efficient. Highly recommended.

Parts Used:

Clark from Tifton, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Burners would not light sometimes

Slide stove out unplug remove cover on back bottom left 3 screws remove wires from old module and plug into new module could not remove old module I glued new to old replaced cover pluged back in slide stove back in and the burners lit

Parts Used:

Surface Burners Spark Module Kit

Robert from St. Remy, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Burnner rusty and will not start with electric start.

Removed and installed burners in less than 15 min with just a nut driver. Replacing the burn ere did not fix the starting problem, but replacing them did improve the hurried flame.

Parts Used:

Robert from Mary Esther, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

old yucky filter

Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!

Parts Used:

Diane from Flower Mound, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

rotten filter for down draft vent

How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!

Parts Used:

Craig from Ashburn, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Needed to replace the grease filter!

Followed the directions. Piece of cake!!

Parts Used:

Colette from Annapolis, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Holes in the air filter of our Jenn-Air grill

Simply pulled the old filter out and put the new filter in.

Parts Used:

Janice from Ocala, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Replacement

This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,

Parts Used:

Barb from Holladay, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

rear burner not working

removed two hexigon screws--removed old burner---placed new burner into stove socket--replaced two screws. Done in about five minutes. Most time used to fine right size socket to fit screws! Fast delivery--easy repair--AND it works!

Parts Used:

Larry from Washington, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

Was this instruction helpful to you?

Filter worn out, exhasut fan kept going off

Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

Parts Used:

John from Cayce, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Front burners would not light.

First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.

Parts Used:

Surface Burners Spark Module Kit

Jeffrey from Columbus, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Burners would not light - rusted

New front burners fit well, but back ones had just enough variance in tne angle of the gas-supply tube that it would not fit the mounting bracket holding both burners in place. I had to grind a small flange off of the bracket so the gas tube would clear. Once that was done the burners worked well.

Parts Used: