- Home
- CS980ST2SS
- Instructions
CS980ST2SS Hotpoint Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
the bottom element of the oven was broken
-
DAVID from PARIS, MI
- Really Easy
- Less than 15 mins
attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!
Was this helpful?
Thank you for voting!
missing meat thermistor
-
John R from Asheville, NC
- Really Easy
- Less than 15 mins
plug in thermistor when needed
Was this helpful?
Thank you for voting!
Oven Probe broke
-
Kathleen from Munt Laurel, NJ
- Really Easy
- Less than 15 mins
Ordered new probe
Was this helpful?
Thank you for voting!
Old bake element burned out
-
Thomas from Hamilton, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and
... Read more
oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.
Read less
Was this helpful?
Thank you for voting!
Broken bake element
-
Marcus from Lagrange, GA
- Really Easy
- Less than 15 mins
-
Pliers
Very easy to install save several dollars
Was this helpful?
Thank you for voting!
Oven light wire broken, damaged socket
-
Patricia from Brandenburg, KY
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this helpful?
Thank you for voting!
8 inch burner was burnt out
-
Luis from Kissimmee, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burn
... Read more
er connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.
Read less
Was this helpful?
Thank you for voting!
Bake Element burnt out
-
Greg from Chicopee, MA
- Really Easy
- Less than 15 mins
-
Socket set
watched the video on part select - took less time then they said.
Was this helpful?
Thank you for voting!
Broiler Element Replacement
-
Emily from Snoqualmie Pass, WA
- Really Easy
- Less than 15 mins
-
Nutdriver
There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to
... Read more
the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.
Read less
Was this helpful?
Thank you for voting!
Heating element not working
-
Stuart from Yelm, WA
- Really Easy
- Less than 15 mins
-
Nutdriver
Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.
Was this helpful?
Thank you for voting!
burned out
-
mary from morton, WA
- Really Easy
- Less than 15 mins
-
Nutdriver
replaced
Was this helpful?
Thank you for voting!
Burned out heating element
-
David from Alice, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
took 5 minutes with a nut driver and son. I had previously watch your video and went exactly as the video described and showed.
Was this helpful?
Thank you for voting!
heating element blew apart
-
Lori from Bellows Falls, VT
- Really Easy
- Less than 15 mins
-
Nutdriver
I watched the video on this website and it couldn't have been easier. The only thing I did differently was I took the door off for an easier reach. To take the door off, you open just a little and pull up. It makes it so much easier to get at the screws, and maked the repair a snap.
Was this helpful?
Thank you for voting!
A large burner (haliant Burner 8" ) went out on my Hotpoint Electric Range
-
Ruth from Potosi, MO
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the
... Read more
range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!
Read less
Was this helpful?
Thank you for voting!
broken light socket
-
James from Monterey, TN
- Easy
- 15 - 30 mins
-
Nutdriver
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this helpful?
Thank you for voting!