CRSH265LB3 Crosley Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light Socket short
- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
Parts Used:
-
Rebecca from Gautier, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
22 of 31 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My fridge temp was warm. Freezer temp was ok, but fluctuated some.
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!
Parts Used:
-
Cindy from AMARILLO, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
25 of 40 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken actuator-water
Easy repair, except the re-install of the entire water/ice part back into the door. The original plastic water line too short to fit back into the small opening. Hint: Go buy 10 inch of new water line and a small connector. Run the new line up through the small opening, and connect to the original water line with the small connector. This made it easy to replace and test, and then cut of the excess water line.
Thanks.
Thanks.
Parts Used:
-
Wesley from New Smyrna Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
17 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fridge side too cold
Most of the time was spent removing frozen food and removing the plastic clip holding one of the shelves in place. Removal of bottom panel took less than a minute. Thermostat easy to find, clipped wires a the unit and removed unit. Used included wire jackets, but not white shrink wrap. This did NOT fix the problem. This was the attempt at a 'cheap' fix. My refrigerator required the 'control box' to be replaced.
Parts Used:
-
Brian from Eden Prairie, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
19 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Guides damaged, crisper pan cracked
1.Got on line to Partselect ordered the parts we needed .they arrived Quickly and in good condition 2.Except the tray was sent in error delaying the repair. 3.contacted Partselect costumer services for assistance 4.Followed their direction and reorder the correct one hoping the correct one would arrive .it did the next day .5.On to repair, removed broken stud with panel stud puller with the aide of a putty knife to spread the pressure of tool stud came out 6.reinserted new stud 7.replaced the new upper crisper drawer cover glass not included . 8.Upper Crisper pan to complete the repair. 9.all in all successful with the help of Partselect superior parts and helpful guides.
Parts Used:
-
Darin from Nicholasville, KY
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
25 of 43 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Glass Shelf Broken
-
ROBERT from DOYLESTOWN, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
23 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 broken shelving supports
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!
Parts Used:
-
Victor from Wilton, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
16 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
shelves in refrigerator broken
Took out and threw away old shelves. Replaced with new shelves. . . no tools required!
Parts Used:
-
Susan from King George, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
19 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer was cold but the fridge was warm. Back panel of fridge was building up frost
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .
The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
Parts Used:
-
Albert from Buffalo Grove, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Wrench (Adjustable)
22 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drip from door water dispenser
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.
Parts Used:
-
Paul from Anderson, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
16 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not cooling
Just took out 4-5 screws and follow the instructions and repair went great
Parts Used:
-
Tony from LAURENS, SC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
16 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker quit working
Followed the steps in the video on your site, really easy to do.
Parts Used:
-
Steve from ORANGE, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
16 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
evaporator coil would freeze up solid. no air flow through coil; no cooling.
-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.
Parts Used:
-
KEVIN from BRONX, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
19 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The ice/light buttons were cracked and broken
First of all, I ordered in the afternoon and the part was on my doorstep the very next day, amazing shipping. I shopped all over and this was the best price by a few dollars. I hope I never need any other parts, but if I do, I will come back to buy my parts here.
I pried the old cover off with a pocket knife and carefully installed the new one. Now it looks great and it only took me about 5 minutes.
I pried the old cover off with a pocket knife and carefully installed the new one. Now it looks great and it only took me about 5 minutes.
Parts Used:
-
Thomas from Schwenksville, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
15 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It Was Fast And Easy, No To Mention Affordable.
Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.
Parts Used:
-
Jim from Herington, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
15 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!