CRG3490GWWA Crosley Range - Instructions

First I removed the two screws that hold the bottom panel I then pulled the panel out and put the new panle in and put the two screws back in

move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Removed the broken door handle with a screwdriver, replaced the new door handle with a screwdriver. Took less than a couple of minutes to make the repair.

removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.

removed the two screws that hold the handle and oven top cap in place. I then pulled the handle and oven top cap up and off the door. This exposed the glass guides on both sides and bottom. I placed the new glass in the guides, replaced the oven top cap by carefully fitting the glass into the top cap and holding the oven handle in place to accept the two screws from the inside of the oven door. Very simple assembly.

Disconnected power, I removed the igniter from oven. Measured the resistance (275 ohms) and then the current draw. DO NOT ATTEMPT THIS UNLESS YOU ARE ABLE TO ACCOMPLISH THIS SAFELY. I made a harness and connected the old igniter to 110 V ac, Current draw thru the meter settled at 2.7 Amps. Too weak to fully open gas valve. Valve requires 3.2 - 3.6 amps to fully operate properly. New igniter measured 300 ohms and current draw was 3.4 amps. Installed new part and everything works fine. Correct part and good service from this site

Twisted replacement bulb into place easily. Let there be light!

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

First I removed the two screws that hold the handler in place. I then installed the new glass in and put the two screws back.

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

took the two screws out by hand, slipped out the ruined panel, slid the new one in place, replaced the two screws...simple as that

Turn off gas,unplug,unbolt the burners(you have to do this to keep from bending and or kinking over the gas lines.Luck kept me from bending the lines out of whack.)All I needed was the electrode but I couldn’t find it available separately.I had to buy the whole front burner.Anyway remove the clip from the new part slide the electrode out.Tilt the top of the range up take the clip off of the old electrode slide it out put the new one in install clip.Plug it in,rebolt all the burners in.Careful not to bend the gas lines.put the top down turn on the gas,plug it in and light.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)