CPLES399EC8 Frigidaire Wall Oven - Instructions

pulled door off took door apart replaced hinge

Husband made install in very short time. Nice to have them back in operation.

Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

I removed the element, plugged in the new one and that has corrected the uneven oven temperature.

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

Removed outer glass first ,then worked my way thru to inner glass..

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

The hinges had just wore out ofter several years of service. We took the Oven Door of, simply and took the hings off and ordered the new ones. VERY EASY TO DO. The shipping, my my goodness Ordered on Thursday noon time and received the items before 4 pm on Friday. I just can't get over how quickly You shipped this item. Thanks You, and I will use You again, should the need arise. H. Briden Culleoka, TN

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

2 People--removed door, then removed and replaced springs followed by door a brief pictorial of the area even printed on the package would have simplified the project

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

Husband/wife effort. We located our manual for removing the door and followed instructions. (It's probably online as well.) With the door off, we removed the screws on the side with the defective hinge, took out the old hinge and put in the new one. In trying to replace the door, we couldn't get the lock (upside-down u-shaped piece on the hinge) to rotate over the hinge lever hook on the new hinge. It looked slightly different than the other side (had a bit more hook on it that was in the way). PartSelect sent a new hinge in case the other was defective. (The first arrived in 2 days; the second in 3. No extra charge. Very pleased with the service!) Same trouble. So we filed off the tip of the hook and were able to move the lock in place and put the door back on. The door is not heavy anymore, but doesn't pull in tightly at the top. We thought about taking it off again and trying to position the new hinge a little better to see if it will fit perfectly (it slants down a little compared to the other side.) But it's not so loose at the top that the oven light comes on, so it's usable the way it is. And it looks good, so we're leaving it.

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.