CPLES399EC7 Frigidaire Wall Oven - Instructions

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Turned off power to oven. Pulled control dial from each element control. Removed plactic nut from each control and removed panel. Marked all connectors to "duel element control" for easy placement on new control unit. Replaced panel and installed plactic nuts. Replaced oven lamps and reinstalled the glass bulb covers. Turned power back on and tested element control that was replaced. Tested oven lamps by opening oven door. Everything went well.

Replaced both springs. Follow instructions in owners manual on removing door. Spring assembly resides in door. Remove screws holding spring assembly in place, then the remaining screws holding the inside of door in place. Raising the side, slide out old spring then slide in the new one - do the same on the opposite side. Replace all the screws - starting with those that hold the spring assembly making sure the latches are straight. Put the door back on making sure to lock "spring locks" detailed in owners manual

pulled door off took door apart replaced hinge

Husband made install in very short time. Nice to have them back in operation.

Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

Removed outer glass first ,then worked my way thru to inner glass..

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Third time was a charm. Following PartSelect repair percentages I first replaced the oven sensor which did not fix problem. Next I replaced the main terminal block and oven baking element. Again , this did not fix problem. Lasty I replaced the oven electronic clock/ timer and the oven started working properly.

The hinges had just wore out ofter several years of service. We took the Oven Door of, simply and took the hings off and ordered the new ones. VERY EASY TO DO. The shipping, my my goodness Ordered on Thursday noon time and received the items before 4 pm on Friday. I just can't get over how quickly You shipped this item. Thanks You, and I will use You again, should the need arise. H. Briden Culleoka, TN

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

2 People--removed door, then removed and replaced springs followed by door a brief pictorial of the area even printed on the package would have simplified the project