All Installation Instructions for General Electric Range CGS990SET6SS

Oven Light Assembly damaged

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

Parts Used:

Oven Light Housing

Jose from Frederick, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

5 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Replaced temperature sensor

un-screw temperature sensor, have to move racks and door, then open back cover board to disconnect the sensor.

Parts Used:

Range Oven Temperature Sensor

George from LANSDALE, PA
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Wrong parts

Your diagram on your website says lower oven is incorrect everything on there is upper oven I ordered the wrong part because your diagrams are all wrong OK

Parts Used:

BAKE DEFLECTOR UC

AMON from MARYSVILLE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter

Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.

Parts Used:

Vision Burner - Extra Large

Dan from WARROAD, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Gas burner wasn’t burning properly

I ordered the new burner head and replaced it and now it works perfectly.

Parts Used:

Vision Burner - Extra Large

Karin from ARUNDEL, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Temp probe was defective

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

Parts Used:

Meat Probe Thermistor

Eric from SOUTHBURY, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven meat probe broken

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Parts Used:

Meat Probe Thermistor

robert from FAIRFIELD, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

flame was inconsistent. too much air.

replaced old with new.

Parts Used:

Vision Burner - Extra Large

Raymond J. from EASTPORT, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

shortage in wiring cause the housing to burn out

Replaced new light housing.
Thanks to you guys for the prompt response

Parts Used:

Oven Light Housing

fred from PALM COAST, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Food ran over the burner and damaged it.It was easy to place it back inII

It only required placing the new burner in the proper location.

Parts Used:

Burner Cap - Black - Medium - 9500 BTU

Alan from PASADENA, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Replace temp sensor in gas range

Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved

Parts Used:

Range Oven Temperature Sensor

Ron from PAINESVILLE, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven sensor not working

Very very simple repair!!!!! Works great!!

Parts Used:

Range Oven Temperature Sensor

Mary from TUCSON, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Water would fill washing drum when off

Remove and replaced water valve, seems to have fixed the problem

Parts Used:

Knob Dial Skirt

joseph from SECAUCUS, NJ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Gas Oven will not light

I was disappointed with this parts recommendation..neither part solved the problem, a first with partselect. The Range Oven sensor change out was easy and straight forward once the back lower panel was removed. The SPARK MODULE was time consuming..the module is located and accessible only by removing the range top. Having gas burners requires unscrewing all the burners before tipping up the top and removing it, then removing the guard over the Module is next..it's a project, sure wish it worked when I was done!..turned out to be the oven glow bar....

Parts Used: