CG200L Jenn-Air Cooktop - Instructions

Replaced the old knobs with the new ones.

Very simple remove the Grill section and install the Burners no reworking of existing Unit is required

This range is about 17 years old and the igniter on the left set of burners had failed in the first month of use. A warranty repairman came, made a big mess, marred the adjacent counter top, spent a lot of time badmouthing Jenn-Air and left without fixing the problem. We have been manually lighting these burners all this time. Now that I am retired, I have set about repairing everything I can get my hands on just to have things to do. I always did this when I was young but got too busy with career and family. One big help is doing things now is you can Google a problem, find parts and instructions how to make the repair which is much easier than all the research you used to have to do. This repair is easy but time consuming due to all the screws that you have to remove to get to the igniter and the controller in the back. Since one side worked I was confident that the controller was good but the problem was only the igniter on the left side. This range is a dual fuel unit and has a downdraft connection so sliding it out from the wall is also time consuming. First pull the breaker at the electric panel. Remove the bottom plate and disconnect the flexible downdraft connection. Hopefully, you have enough flexible gas line so you can slide stove out to reach the back without having to shut off the gas and removing the connection. Next you remove the grills and burners. Then you have to remove all the screws connecting the top of the stove. There are nuts and washers that surround the gas jets that you can remove to partially lift the drip pan so you can unscrew the old igniter and install the new one. Next remove the back and see where the igniter control is located. Disconnect the old wire, install the new wire in the guides and insert in the controller. At this point all you need to do is put everything back where it was. This does not take a lot of know-how just time and patience. It makes you wonder why an "expert" could not have done this easily.

took old burners out, installed new ones . I was very easy and if i could do it anyone can. I used a rachet and thats the only tool i needed

The repair was extremely easy. My stove still worked but looked awful. By changing out these parts it makes it look brand new.Thank you.

Slide the knob onto the shaft.

The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten

wanted a fresh clean look on the burners since they were old and getting dirty and blackened from use. Easy to replace with new one.

Found the part number on an old box, ordered the part and it arrived next day. Installed easily and is working perfectly.

The issue: the burners were abused by the previous tenant, the burnt grease was clearly visible. They would hardly ignite and the smell of gas was always present.The remedy: new burners. They were hard to find, I was not completely sure about to stove model (it could be quite a search to find the right ones). There is a front burner and a back one. I was not sure from the diagram about the back one, so I called Partselect and someone answered the call right-away. The burners arrived a few days later, and they were the correct ones. The burners are not Jenn-air specific, it looks like several brand names use the same ones. The installation was extremely easy, a few hex screws. The stove is like new. I highly recommend Partselect.

I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill

Pop off the old and on with the new. Took longer to open the plastic packaging each came in than to remove & replace old knob with new.

I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.

Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete