All Installation Instructions for Jenn-Air Cooktop CG200B

only one burner on the cooktop worked

Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)

Rear Burner

William from Chipley, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

One burner knob melted and one had a broken "stem"

Pop off the old and on with the new. Took longer to open the plastic packaging each came in than to remove & replace old knob with new.

Parts Used:

Surface Burner Knob

Joan from Egg Harbor, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner was not lighting

I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)

Luciano from Hollister, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Nroken Burnner knob

Slide the knob onto the shaft.

Parts Used:

Surface Burner Knob

William M. from Rock Hill, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Filter was very old and falling apart.

The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten

Parts Used:

Range Grease Filter

June S from San Antonio, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

replacing old parts

wanted a fresh clean look on the burners since they were old and getting dirty and blackened from use. Easy to replace with new one.

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)

Debra from Carlstadt, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Range burner melted plastic jar and became clogged

Found the part number on an old box, ordered the part and it arrived next day. Installed easily and is working perfectly.

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)

Harry from Cambria, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

Was this instruction helpful to you?

bearing went out in blower motor

removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok

Parts Used:

Blower Motor

Range Exhaust Vent Blower Wheel

richard from white castle, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

Was this instruction helpful to you?

Burners would not light - rusted

New front burners fit well, but back ones had just enough variance in tne angle of the gas-supply tube that it would not fit the mounting bracket holding both burners in place. I had to grind a small flange off of the bracket so the gas tube would clear. Once that was done the burners worked well.

Parts Used:

Rear Burner

Range Front Burner Assembly Black (Glossy Finish)

Bob from Mansfield, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Front burners would not light.

First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.

Parts Used:

Surface Burners Spark Module Kit

Jeffrey from Columbus, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

old burners wouldn't light

took old burners out, installed new ones . I was very easy and if i could do it anyone can. I used a rachet and thats the only tool i needed

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)

Rear Burner

BOB from hartford, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Old and stained

The repair was extremely easy. My stove still worked but looked awful. By changing out these parts it makes it look brand new.Thank you.

Parts Used:

Rear Burner

Range Front Burner Assembly Black (Glossy Finish)

Range Burner Bracket (Black)

Susan from South Lake Tahoe, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Worn out burner grates

Lift and replace. This was the only web site that gave a picture with the correct size of the grates I was looking for. All the other sites gave approximate sizes and universal part numbers instead of the vendor part number. That is why I bought it here. I didn't want to have to return the product because it was off just a bit.

Parts Used: