CFW4700LW0 Crosley Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Door Striker
Removed two phillips screws. Removed old door striker. Replaced with new door striker. Replaced old phillips screws. Job takes less than 1 minute.
Parts Used:
-
Robert from Hyattsville, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Would not go into spin cycle
Took off top. Removed 2 screws on Door Lock Assembly and replaced.
Parts Used:
-
Jim from Dyersburg, TN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door lock mechanism broke and washer would not run
You must remove the top of the washer with screws on rear of washer. Top slides forward to remove. Once top is removed you can reach door lock mechanism from the top. Two screws must be removed from the front of the washer where lock enters mech. You can grab the mechanism from above by the wires that run to it. Undo wiring harness and insert new mehanism. Slide into place and attach in the front of washer with screws. This job is easy and can save you a lot on repair bills!
Parts Used:
-
SCOTT from SALINE, MI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replaced Door Strike.
-
Lee from Kansas City, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The door strike just broke (who makes a plastic door strike on a machine that gets used as much as a washer?)
-
Dulcenee from Bloomington, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer did not operate due to frontloader door not locking
Watched your supplied video on how to repair. I did not want to break the washer door sealas described on the video. I removed the two screw on the back of washer that held the top and then slid the top off. I moved the two screws securing the switch at the exterior door. I changed the door lock and switch assembly through the top by moving the connectors one at a time from the old assembly to the new. Replaced the screws to complete. I then changed the door strike by removing the two screws and replacing the new strike. Job complete and washer works fine saving us $200.00. Thank you ever so much PartSelect.com.
Parts Used:
-
David from Freeport, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The door strike broke
It took all of five minutes, two screws and done. Saved $150.00 on the service charge, while the part cost less than $15.00 for the parts including S/H.
Parts Used:
-
Vernon from Chesapeake, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door strike broke while moving
-
Shari from Raleigh, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Would not fill with water
Installed New shock absorbers and new door strike. The existing broken shock absorbers caused the drum to oscillate and pull wires from door lock switch.
Parts Used:
-
clyde from tunkhannock, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Door Strike Broken off in lock
The end of the door strike had broken off in the lock. The door strike itself went on in just a few minutes. The time consuming part was getting the piece that had broken off out. After trying with tweezers to get it out, we took the lock off the machine and finally got it out. So....if the door strike looks damaged or isn't shutting properly, replace it before it breaks off inside the lock. We were pleased with how quickly it came. We ordered it Sunday evening and it came Tuesday morning.
Parts Used:
-
Linda from Parkersburg, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door Lock and switch didn't work
Using a youtube video, (which might have actually been related to parts select), the door lock replacement went smoothly AFTER I couldn't SEE the SPRING around the rubber boot, as the spring was the SAME color and with a little bit of dust on it, was indistinguishable. As soon as I found it, the rest was fairly simple. I MIGHT even try replacing the moldy boot on these stupid front loaders...I paid for overnight shipping as I also had Geek squad guys on hold for repair, and needed to know fast, whether or not this would do the trick. HOORAY!
Parts Used:
-
Christine from Bedminster, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door would not latch and washer failed to start
Remove the 2 screws on the rear of the top panel. Open door and remove the 2 screws holding the latch assembly. Reach down and pull up latch. Remove the 3 wire connectors. Plug wire into new latch and re-install in reverse order.
Parts Used:
-
Stanley from Centuria, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door would not lock shut
Everything went great, except replacing the rubber seal, that was a little bit harder to put back in place. But other then that, went very well and easy to repair.
Parts Used:
-
Sharon from Tampa, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
broken doorlatch
Remove the top cover and the doorlacth and unplug the old parts as simple as that
Parts Used:
-
ricardo from nesa, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
plastic end of strike broken
I didn't have the right tool, so asked my handyman neighbor to come do a few projects and he had the driver in his pocket screw driver. it is a tip that is included in many multi-tip drivers. two screws removed the old and replaced the new. cheaper than local parts place, and no repair man. thanks
Parts Used:
-
Janet from Boise, ID
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!