All Installation Instructions for Crosley Freezer CFUFH17LW4

no bin doors

slipped in the new bins very easy

Parts Used:

Door Bin - 2 Liter

ben from eden, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Fan would not start occasionally

I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.

Parts Used:

FAN MOTOR EVAP 115V

Mike from Satellite Beach, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Replaced drawer slides L & R

Removed three screws each side to remove old slides. Needed spacers under new slide so that drawer would stay on track. Cut old slide to make spacers and installed both slides in 15 mins.

Parts Used:

Drawer Slide - Left or Right Side

Richard from GAINESVILLE, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Noisy fan

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Parts Used:

FAN MOTOR EVAP 115V

CRAIG from PRESCOTT VALLEY, AZ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Freezer only cold on bottom

Pulled freezer out from where located to allow shelves to be removed.Unplugged unit, removed shelves and evaporator cover, installed new fan motor. Plugged unit up to check fan motor operation. Reassembled unit, installed shelves and moved freezer back into original location.

Parts Used:

FAN MOTOR EVAP 115V

Shelf End Cap - Right Side - Tilt-out

Shelf End Cap - Left Side - Tilt Out

Richard from Warren, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Lighting Strike Brunt Out Controll

Removed controll with srew driver plug in new conrol

Parts Used:

Electronic Control Board

EDDIE from SALISAW OK, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Freezer Control Went Bad

I order a new controll unit and it arrived the next day. Installed the new unit and we were back working. Great service. Thank you very much

Parts Used:

Electronic Control Board

donald from medina, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

stop-basket was broken

I stuck the new stop-basket in the hole where it belonged.

Parts Used:

STOP-BASKET

Kenneth from Tahlequah, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Side rail for sliding shelf would not stay tight

The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.

Parts Used: