CFHT1843LW8 Frigidaire Refrigerator - Instructions

I simply loosened the screws holding the refrigerator door handle and then slid the bottom portion of the handle off from the screw holding it in place. The bottom portion of the handle did not exactly marry-up with door, showing a very small gap. I attributed this to the age of the appliance.

R&R DOOR SEAL VERY EASY TO INSTALL THANKS TO ALL

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

I tried contacting this page about the item I never received but I never heard back so this is my review. I DIDNT FIX IT BECAUSE I DIDNT GET ITEM.

It was extremely easy. I opened door, unscrewed the two (2) screws at the top of the door handle with a phillips screw driver. Once screws were out I rotated the handle to the left and unhooked it from the mounting block. The new handle was already equipped with a mounting block. I attached the new handles mounting block to the door and rotated the handle up and positioned the holes to the holes on the door. I used the same 2 screws from the old handle and tightened them into the handle and door. That was it. Very easy.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

After checking the capacitor and 3 in 1 starter run relay for continuity and both measuring , I was able to remove the old parts and install the new parts for the refrigerator after unplugging the unit. I also checked the new parts prior to installing. I also went on Parts Select and watched some very helpful videos. Thanks a lot for your help desk for going above and beyond to ensure that I ordered the correct part! ????

Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.

replaced broken one

Slid the old shelf out. Attached meat drawer to new shelf and slid it in.

There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.

I used Gorilla glue to replace the handle at the screws-pressed hard and left to dry. The replacement handle (s),( had to buy two-guess the manufacturerer expects the other one to crack too!) are hanging in the garage until the glue releases, if it does. NEVER had a refrigerator handle crack before and I am 81 yrs old. Product made to be defective as this is the second repair I've had to have on this refrig., other one a just under 1 year and concerned the freezer dripping water. The refrig is within 2 yrs. Yikes!

The part fit perfectly. I simply placed the ends on the holes on the side wall inside the refrigerator, and the other end of the shelf slipped right into the matching holes on the other side. That easy!