All Installation Instructions for Frigidaire Range CFEF3007LBA

Oven Racks needed to be replaced.

Slide out the old; slide in the new!

Parts Used:

Oven Rack

Peter from Chicago, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner wouldn't stay hot.

I pulled out the old element and the new one just plugged right in.

Parts Used:

Surface Element - 8 Inch - 220V

Billy from Lovelady, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The stupid baking element died on CHRISTMAS EVE!

My husband removed the old one in a few minutes, the just popped the new one in when it came. Not for nothing, (where we purchased the stove) wanted $67 for the same part you all charged $49.00

Parts Used:

Bake Element - 240V

Minda from Madras, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

12 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Draw Glide Broken Off Bottom Drawer.

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

Parts Used:

Rear Drawer Glide

Kathleen from fall river, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No LED read out and no function!

I tested incoming and outgoing voltage at the timer! The timer showed to be defected!

Parts Used:

Electronic Clock Assembly

Rick from mount airy, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Enement was blew out.

I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.

Parts Used:

Surface Element - 6 Inch

Chhabildas from Charlotte, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

9 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replacement burner

Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery

Parts Used:

Surface Element - 8 Inch - 220V

Donna from Westfield, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Electric burner switch shorted out.

First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Parts Used:

Infinite Burner Switch

Armando G from Alice, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

9 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom elerment burnt into

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Parts Used:

Broil Element

Danny from Gaffney, SC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Large burner wouldn't heat

Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Parts Used:

Infinite Burner Switch

Phyllis from Elberon, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

15 of 31 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broil element was bad.

It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Parts Used:

Broil Element

William from Fort Myers, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Socket set

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven light bulb went dark; it needed replacing

Twisted replacement bulb into place easily. Let there be light!

Parts Used:

Light Bulb

Lise from CEDAR GROVE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

9 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Both front burners began heating too fast and too high. One damaged the finish on the splash pan.

At the Frigidaire parts website, I found the parts and saw that there are videos that show how to replace the burner controls. In brief:
1) Slide the range/oven out so you can get to the back of the control hood.
2) There are three screws that hold the cover in place (the video showed four).
2a) The video also suggests using a #1 square bit. I found that there was indeed a square hole in the caps of the screws, but they also had a hex head that a 1/4" hex nut driver fits. So I used that.
2b) Be careful taking out the last (top center) screw. When it comes free, the cover can drop and bruise or cut your foot or the floor. Having a helper is worth it!
3) The switch for the larger elements has a red dot on front and back. Match it with the one in place that has a red dot. The switch for the small element doesn't have a dot.
3a) Holding a new switch in your hand, remove one wire at a time from the switch in the control hood and put it in the same place on the new switch. I found that for my stove, there was a fixture holding two wires and another holding three wires. This made it impossible to put the wires on wrong.
3b) When all wires have been transferred, pull off the control knob in front and unscrew the two screws that hold the old switch in place. Take out the old switch and replace it with the new switch.
3c) Use the two screws to attach the new switch in its place and replace the control knob.
4) Repeat for as many switches as you purchased. I did all four.
5) Replace the cover.
6) Slide the range back into place.

I found black deposits on all the switches, that must have come from a contactor inside, so I was glad I replaced them all.

Another tip: while the unit is out, clean off the sides and back that you couldn't get to while it was in place. For us, this took as long or longer than the steps above for replacing the switches.

Parts Used:

Infinite Burner Switch