CFE28TP3MBD1 General Electric Refrigerator - Instructions

Left side was broken for about 8 years. Back of glide would fall down about every 4 months. This time the upper basket jammed up on the glide and the freezer drawer would not close. Had to break it to remove the upper basket.

From the time the parts were delivered and installed two Glide Supports, it took a total of 30 minutes. If that long. Before I ordered the part, I made sure I had the socket to fit the nut and that I was able to remove it. I removed the broken one after ordering.

PartSelect was the only website that I could find that carried the part.

Replaced Temperature Sensor and now it is getting cold.

Exposed evap defrosted with heat gun exposed defrost element defrost termination switch ok therminster didn’t check out the thermistor sends the signal to logic panel then run the the freezer ice machine and refer temps it took 24 hours before the system starting to show results freezer compartment 10 below ice compartment 0 degrees refer temp 37 degrees one refrigerant three different temps system is running at optimum performance 450.00 $ service call the thing with GE appliances there is no wiring diagram .thankyou parts select .ill use you on all domestic service calls.

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

Snap filter into place while holding the filter slightly away from the refrig. When filter snaps into place, push it towards refrig into place.

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.

I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

replace sensor in refriger.