CF1540 (Type 0) Porter Cable Compressor - Parts

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

It is an OEM component which is designed for use with air compressors. This special nut sleeve assembly secures the pressure relief tube to the pressure switch. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. One durable metal nut sleeve assembly is included. A wrench will be needed t...Read moreo perform this repair. Check the appropriate diagrams for your model to ensure the proper replacement procedure. Make sure to drain the air before starting this repair.

This is an authentic replacement part manufactured for use with Porter Cable air compressors. The safety valve is used to prevent the tank from overpressurizing by letting air out of the tank when a specific pressure is met. Safety valves have specific pressure tolerances specific to the model of air compressor it is important to match th...Read moree valve to your model of compressor. This safety valve is available as an individual replacement part.

This is a genuine replacement part manufactured for use with air compressors. This hex head screw has many applications from fastening the connecting rod, to securing the isolators. The screw is sold as an individual replacement part, please see model diagram for part location and usage.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling • The O-ring has ragged, tattered edges. Thes...Read moree are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is a genuine replacement part manufactured for use with air compressors from DeWalt. This part creates an airtight seal between the elbow and the tube. You may need a wrench to replace this part. This assembly but sleeve is sold individually and made of metal.

This replacement screw is a genuine OEM sourced item commonly utilized on air compressors and pressure washers. It is a standard hardware which has multiple applications depending on the unit. Please make sure to check diagrams of your model for the correct location and used of this screw. This part is made from durable metal and it is sold individually. You will need a wrench to install or remove this hardware.

This rod kit is an original part from Craftsman for air compressors. This part attaches to the piston to the crankshaft that is in the pump. This kit includes the following: cylinder head, piston, cylinder head gasket and piston ring. You will need a wrench set and socket set to replace this part. When installing this part, it is recommen...Read moreded that that you fasten the top screw (50-60 inch- pounds). This kit is made of metal and rubber.

This is a genuine replacement part sourced from the original manufacturer for use with air compressors made by Craftsman. The user will need to replace this screw if it is missing or not working correctly. This part is made of durable material and sold individually.

This saddle mount cup is an OEM direct from Craftsman for air compressors. This part holds the screw in place. You will need a wrench to remove the bolts that go through it. It is recommended that you wear gloves when replacing this part. This saddle mount cup is made of steel and sold individually.