CEC1M1WTAB Gibson Range - Instructions

Really easy process. First I unplugged the oven for safety then I proceeded to remove the 2 screws that were holding the old element in place. Next I removed the old element then installed the new one. After installing the two screws I connect the oven back to its power source and BANG!............. It works like a charm

I give it a A+ installation

I unplugged the stove and used a flashlight for light. I tried a phillips head, but it was too big. I then got a set of pliers and unscrewed the two screws an pulled out the element. I removed the 2 electrical plugs from the ends of the element and attached the new ones. They went on from the top where as the old ones slid from the side. after pushing the element back in i screwed the screws back in and the backings were a tad large so I bent them up and presto it was fixed!

Pulled stove out, removed screws that hold the element in place. Then pulled element out a few inches, diconnected the two wires. I connected the wires to the new element and put everything back to right. It was quick and easy.

Loosened the two nuts that hold the element in place. Gently pulled the old elementr forward to expose connections. Disconnected the old element and attached the new element. Slipped the new attached element through the holes being carful not to disturb the insulation. Once the element was in the correct position with the tabs against the back wall of the oven replaced the two nuts and the job was complete. The whole job took approx. 5 minutes. It was very, very easy.

First my husband removed the two screws that held the heating element into place. I had tried it with pliers which didn't work well. But with the proper socket the screws came loose easily. He pulled the heating element out a few inches and detached the wires. He then slipped the wire over the new heating element and screwed the new element into place. Now we can bake again. Very easy and we received the part quickly.

Oven is an in the wall unit. Normally it is an unplug and plug in. The old one had a melted connector, so the connector had to be cut off and replaced as well. Be sure to turn off the electricity at the braker to be safe, first.

If I didn't need my oven ASAP, I would not even have attempted to do this repair before my husband came home. But he wasn't going to be home for hours, and I needed it now!
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the oven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!

Thanks,
Vicki

Removed back cover, unhooked wires, unscrewed and removed bad baking element. Reverse order to install. Less than 15 min. repair job.

First unplugged the stove, then removed the screws holding the element in place. Next I pulled the element out until the wires were visible and unplugged them. After removing the old element, I plugged the new one in and positioned it with the screws. Plug the stove back in and done.

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Cut the old block off tied new wires to hot wires . That easy!

followed the video provided on line which was very helpful..

Open the door and slide in the new rack.

Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.

Plug the new element into the space on stove