CE30M5DRAA Tappan Range - Instructions

I could see a visible burnout on the element.
Got it really fast.
Removed two screws, pulled it out, disconnected two wires. installed a new one in, and was done!

I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
Really really easy . I am a single woman with no repair experance and had no problems.

Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.

I was extremely pleased with the very quick delivery of needed parts.

Make sure whichever surface element you are to replace is OFF.Carefully remove surface element by pulling it out of socket and remove drip bowl. Cleaned area around range top and place new or old drip bowl in place. Line up drip bowl cutouts and place on range top and simply push in/plug (2 prongs)in new surface element and place on drip bowl. It's that easy! To install 2 new surface elements and drip bowls took less than 5 minutes.

installed terminal block kits and burners worked great

Just placed the chrome bowl trays in place and was good to go. They look very nice.

I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.

Removed heating elements and replaced drip pans. And by the way, this is the only 'pans' I could find to fit. Thanks.

Removed back access panel of oven (several screws). Unplugged element wires (two slip connectors). Removed two element mounting screws from the inside of oven, and removed old element. Reversed proceedure to install new part.

simple ratchet extension and socket to remove screws and replace. be sure to crimp the connectors with pliers before ataching the element.

took out the two screws pulled the element out unplugged the wires, plugged in the new element, stuck the element back in the holes and put the screws back in

Probably a good idea to either unplug unit or make sure oven is in off position first, then remove screw on either side of old bake element, then gently pull out about 3 inches to expose wire connections and carefully disconnect each slide-on connector. Dispose old element in trash and replace with new one from partselect.com in reverse order. Very simple and much less expensive than either buying a new appliance(if you've been satisfied with what you have), paying a repairperson to come in and/or trying to hunt down the right part from a "local" appliance store/warehouse. The part was easily identifiable via the graphic depiction on the partselect.com website, arrived in excellent condition and in record time for normal ground shipping(less than 2 days from order date!), and I experienced kind and competent customer service from the get-go. A do-it-yourselfer like me really can't ask much more than that when it comes to appliance repair!

I pulled the range out of its space, disconnected the power cord, disconnected the two electic power wire on the heating element. Then I disconnected the two retaining nuts on the inside of the oven and pulled the heating element out. Then reversed the order and wala, hot oven and now my corn bread does not burn.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!