CDWT980V05SS General Electric Dishwasher - Instructions

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

Easiest repair ever. My new rack arrived in three days, opened the box and slid it in. Better quality than the original. Excellent service!

After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.

The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.

So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!

Removed dishwasher from under counter. Removed both cable pulleys and bushings. Threaded new cables and remounted pulleys and bushings. Finally stretched springs onto cables. Checked counter balance and reinstalled dishwasher.

The noise came from the dishwasher door. Removed the Phillips screws from the door edge to gain access by separating the front of the door. Had to disconnect some of the electrical connectors to allow more access. Disconnected the blower motor connector. Removed the screws holding the motor assembly and removed the blower motor. Installed the new blower motor and reconnected the electrical connectors. Reassembled the door and cycled the dishwasher. Very quiet now!

shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.

Repaired the soap dispenser.

Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.

Purchased new $1400 dishwasher from sales floor for $699. Cosmetically perfect, but missing drain tube and clamp. Seemed like a good deal... and it was. Needed parts were $34. Install of this machine was a breeze, and it is suoer quiet...I need to get down on the floor and listen for water flow to know that it's working. Really.

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.