All Installation Instructions for General Electric Range CC2S985SET6SS

bakeing element burned out

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

Parts Used:

Bake Element

Bob from Surry, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

F2 error when oven was heating up, along with a beeping noise and then it shut off

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Parts Used:

Temperature Sensor

Lori from Paris, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

None

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

Parts Used:

Bake Element

Nicholas from Poynette, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Bake element burned out

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

Parts Used:

Bake Element

Barry from Malvern, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

oven was not getting up to temp

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Parts Used:

Temperature Sensor

walter from townshend, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

no heat in oven

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

Parts Used:

Bake Element

ronda from kingston, OK
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

F2 error code

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Parts Used:

Temperature Sensor

jud from gatesville, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Flashing F2 and erratic temperature readings.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Parts Used:

Temperature Sensor

Kenneth from Salem, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

the bottom element of the oven was broken

attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!

Parts Used:

Bake Element

DAVID from PARIS, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

oven not warming, f2 indicating overheat

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Parts Used:

Temperature Sensor

David from Lisle, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Bake Element burnt out

watched the video on part select - took less time then they said.

Parts Used:

Bake Element

Greg from Chicopee, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

Was this instruction helpful to you?

The Original burner broke

Just push the burner knob in.

Parts Used:

Burner Knob

Gloria E from Walnut, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Old bake element burned out

Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.

Parts Used:

Bake Element