CBC980SN3SS General Electric Range - Instructions

Use a 1/4" nutdriver and remove the screws that are on the bottom corners of the range top.Prop up the range top high enough for ease of using 1/4" nut driver. Take a picture of the wiring for future reference on re-installing wiring. Note arrow location on burner and remove 1/4" screws holding the clamps to the burner in place and place to the side for re-install on new burner.Remove wiring off old burner.Hold new burner in place with arrow location in previous location and notice holes where clamps will go. Screw clamps on burner using original screws and snap in mounting slots on stove.Re-install wiring.Lower range top and re install 2 screws , 1 in each corner under range top. Test for proper operation and enjoy!

Easy

Remove and replaced water valve, seems to have fixed the problem

The unit has two spring clips that hold it in place. Also two screws that hold the element to the clips. It comes apart ok but doesn't go back as easy. I didn't remove the top as there was room to work from under it.

My daughter held the top down against a wooden dowl i was using as a prop rod . My wife held the unit in place . I finally got the clips back on and the screws back in . Centered the unit , transfered the wires , and it works perfect . Only three people and 30 min.

Thank you PartSelect for all your help !!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

Replaced it

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!

Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid door back on and done. 30 minutes at most.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .