C3001 (Type 01) Porter Cable Compressor - Parts

This is a genuine Craftsman replacement part that has been sourced from the original manufacturer to be used with air compressors. The carbon brushes are used to relay electricity from the switch to the motor's armature. These brushes are priced and sold as a pair because two brushes are required.

This is an original replacement part manufactured for use with Porter Cable air compressors. This gauge is used to measure the air pressure that is set by the regulator. This gauge is threaded and screws directly into the regulator and the gauge is sold individually.

This genuine OEM replacement kit is designed for use with select air compressors and includes essential components to restore proper function. The kit comes with a piston rod, compression ring, cylinder sleeve, and bearing—ideal for repairing worn or damaged internal parts. Please note that this kit does not include the valve plate, head ...Read moregaskets, or any other compressor components, so be sure to check your model’s requirements before beginning repairs. Installation requires basic tools: a screwdriver, hex key Allen wrench), and pliers. With these tools and a bit of care, you can perform a straightforward repair that helps extend the life and efficiency of your compressor.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions, and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by te...Read morension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. This safety valve has a thread sealant pre-applied, so additional thread sealant is not required, the safety valve is sold individually.

When using an air compressor, moisture naturally builds up inside the tank as air is compressed. If this water isn’t drained regularly, it can lead to internal rust and damage over time. That’s where the drain valve comes in—it allows you to release the built-up water and keep your tank in good condition. Located at the bottom of the tank...Read more, this valve should be opened after each use to prevent corrosion and extend the life of your compressor. If you tend to leave air in the tank for long periods, water accumulation can be even more significant. This replacement drain valve features a thread size of 18 TPI and is sold individually. Regular maintenance with a working drain valve helps ensure safe and efficient compressor operation.

This is an OEM part sourced directly from the manufacturer. The belt is commonly found in Craftsman air compressors. This part is made of flexible rubber, and is used to transfer power between the piston and the pump assembly. Over time, it may become cracked and brittle, requiring replacement. You may need an Allen wrench or hex key when replacing this part. This item is sold individually.

This replacement hose clamp is designed for use in various compressor models and serves an important role in securing hoses to specific parts of the unit. Whether you're performing maintenance or replacing worn components, this clamp helps ensure a tight, leak-free connection. Made from durable metal and sold individually, it’s easy to in...Read morestall and built to withstand the pressure and vibration common in compressor operation. If your hose feels loose or you're noticing air leaks, replacing the clamp can help restore proper function and keep your compressor running smoothly.