C2002 Porter Cable - Overview
Models starting with C2002
Click on the best match to narrow your results.
- C2002 (Type 2) Porter Cable Compressor (1HP 6 Gallon Compressor)
- C2002 (Type 8) Porter Cable Compressor (1 HP 6 Gallon Compressor)
- C2002 (Type 7) Porter Cable Compressor (1 HP 6 Gallon Compressor)
- C2002 (Type 4) Porter Cable Compressor (1 HP 6 Gallon Compressor)
- C2002 (Type 5) Porter Cable Compressor (1 HP 6 Gallon Compressor)
- C2002 (Type 3) Porter Cable Compressor (1HP 6 Gallon Compressor)
- C2002 (Type 9) Porter Cable Compressor (1hp 6gal Compressor)
- C2002-WK (Type-6) Porter Cable Compressor (Porter Cable C2002-Wk-Type-6 Parts)
- C2002-WK (Type 3) Porter Cable Nailer (Finish Nailer)
- C2002-WK (Type 4) Porter Cable Compressor (A 1.5hp 6g Pc Um 1stg 120)
- C2002-WK (Type 5) Porter Cable Compressor (A 1.5hp 6g Pc Um 1stg 120)
- C2002-WK (Type 7) Porter Cable Compressor (A 1.5hp 6g Pc Um 1stg 120)
- C2002-WK (Type 0) Porter Cable Compressor (1HP 6G Compressor)
- C2002-WKPIN (Type 1) Porter Cable Compressor (C2002-Wkpin W/ Bonus Pin1)
- C2002M-WK (Type 1) Porter Cable Compressor (Compressor)
- C2002R (Type 9) Porter Cable Compressor (Compressor)
Keep searches simple, eg. "belt" or "pump".
Common Symptoms of models starting with C2002
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Worn piston rod and sleeve
Disassemble plastic housing around compressor unit using appropriate tools. Remove the four bolts from the compressor head using a 5/16 nut driver. Carefully remove head assembly including airline. Remove bolt through rod bearing with Allen wrench.
Reassemble with new rod and piston assembly. Best to use blue locktite on bolt through rod bearing when reassembling. Make sure to torque all bolts to specs listed.
Reassemble with new rod and piston assembly. Best to use blue locktite on bolt through rod bearing when reassembling. Make sure to torque all bolts to specs listed.
Parts Used:
-
Donald from BRYAN, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Can't find this special screw used on many housings etc
Actually don't like using Torx bits because they are hard to center deep in the channel. I had misplaced these forcing me to order replacements.
My plan is to insert Torx bits before screwing in and using jb weld to secure the bit to the screw, giving me a hex head. Can't find this special screw with a hex head. This screw is called AGC-408 by craftsman.
My plan is to insert Torx bits before screwing in and using jb weld to secure the bit to the screw, giving me a hex head. Can't find this special screw with a hex head. This screw is called AGC-408 by craftsman.
Parts Used:
-
Tim from Tucson, AZ
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The compressor was getting air
Put the seal in and it ran like a champ. No vacuum leak and it now runs again!
Parts Used:
-
Linda from CARO, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set, Wrench set
3 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!