BX521VE (P1325033W B) Amana Refrigerator - Instructions

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

I ordered the part and it arrived VERY quickly and was very easily installed. I was delighted that it was something I could do myself and didn't have to bother my husband. Victory! I would order parts from here again if the need should arise.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

I entered the model number and was easily able to find the replacement part I needed. It arrived two days later and I installed it and now my fridge works as good as ever. Thanks I felt so smart.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

I have never used the ice maker because I have a well and didn't want to usewell water to make ice. I usually make ice with bottled water.
I decided to try making ice with gravity fed water from a converted water fountain placed on a higher level than the refrigerator, locater in my garage next to the kitchen.
When I looked at ... Read more the rear of the frig. I saw a copper pipe (on the bottom of the frig.) that lead to a valve, with a plastic tube that went to the freezer. I didn't think that the gravity fed water could go down to the bottom and return to the freezer at the top, so I cut the plastic tube, and fed the water directly to the ice maker.
I only put a small amount of water in my water source because I wasn't shure what would happen. The water filled the tray and the rest of the water went to the container that catches the ice.
I did get one tray of ice. I later found that the valve that the copper pipe went to, has a 7 minute timer that only allows a small amount of water to pass.
My next effort will be to connect to the copper pipe and see if it will allow the gravity fed water to rise to the ice maker. Wish me luck

the shelves are designed to just pop in. So, we easily just put in the new shelf. I was thrilled to be able to easily find, order and replace a shelf. Now my refrigerator is as good as new. I would give this site 4 stars.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sin ... Read more cerely, Ron Marshall, Billings, MT

Slid the new one into place. The only issue was refastening the plastic holders into which the shelf slid. Once I figured out how they reattached, it was no problem.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a ... Read more single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mo ... Read more unting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.