BISW42EKB General Electric Refrigerator - Instructions

All Instructions for the BISW42EKB
91 - 105 of 106

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.
  • Steve from Canyon Country, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.
Was this helpful?
Thank you for voting!
The auger in the ice bucket was rusted
  • Frank from Temecula, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .
Was this helpful?
Thank you for voting!
rusty auger tainting ice
  • JoAnn from Argyle, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was so easy! I seldom attempt any household repair because I have a husband that can fix anything, but he was not available. One screwdriver & remove 4 screws attaching the existing front to old auger/bucket. Line up the screw holes on new bucket with old front, put the 4 screws in through those holes tighten screws & I was done.
Was this helpful?
Thank you for voting!
auger and bucket neded to be changed because of rust which caused the auger and other metal parts to rust which created an unpleasant odor in ice and freezer. to
  • Joan from Colleyville, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The part arrived promptly but was defective. Upon learning of the problem by PartSelect a new part was shipped and was delivered incredibly quickly. Installing it was easy and took only about 5 minutes. We were pleased with the speed in sending the parts and the ease of installation. We will call on them again if necessary because of their good business practices.
Was this helpful?
Thank you for voting!
switch wouldn't come out anymore and turn light on
  • Cynthia from Seatac, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this helpful?
Thank you for voting!
Ice crusher was broken, putting plastic in ice.
  • Joe F. from Kountze, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Ordered Auger and Ice Bucket Assembly All I had to do was install 4 screws. Worked great. Thanks.Joe
Was this helpful?
Thank you for voting!
Ice bucket assembly broke
  • William from Collierville, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Ice bucket and auger came fully assembled. Just had to attach the face plate from the broken ice bucket assembly and slide it into the freezer. There were only four Phillips screws involved.
Was this helpful?
Thank you for voting!
The Ice Bucket was misssing from a Rental Unit .
  • FRANTZ from PLANTATION, FL
  • Really Easy
  • Less than 15 mins
I just put the Ice Bucket under the Ice Maker.Problem solved.
Was this helpful?
Thank you for voting!
Auger and Ice Bucket for GE side by side was rusty
  • Jay from Jacksonville, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
followed the previous posts, loosened four screws on the front panel, attached panel to new auger and ice bucket, and was good to go. Excellent advice!
Was this helpful?
Thank you for voting!
sticky switch
  • ANTHONY from NEW EGYPT, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this helpful?
Thank you for voting!
Replace Auger And Ice Assembly
  • GUSTAVO from CORONA, CA
  • Really Easy
  • Less than 15 mins
Just replaced the auger from the old one
Was this helpful?
Thank you for voting!
The silver plating on the auger was coming loose, rusting and getting in the ice cubes.
  • Terry from Cocoa Beach, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
All I had to do was remove four (4) screws from the old ice bucket assembly to remove the front cover and attach it with the existing screws to the new ice bucket assembly. It was a very simple repair. Thanks for the expedient delivery and the exact replacement part that I needed.
Was this helpful?
Thank you for voting!
The Ice Bucket had rusted
  • Leticia from El Paso, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was really simple, remove 4 screws form the old cover and put it on the new bucket. Simple, Simple!!
Was this helpful?
Thank you for voting!
would not dispence ice
  • jimmy from saluda, SC
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
remove ice bucket and replace broken augar
Was this helpful?
Thank you for voting!
no water to ice maker or water dispencer
  • craig from sweeny, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
replaced circuit board and water solenoids
Was this helpful?
Thank you for voting!
All Instructions for the BISW42EKB
91 - 105 of 106